IP Camera Accessories | Mounts, Enclosures, Lenses, IR & Power

Deployment Considerations

Environmental protection and weather resistance
Mounting stability and load support
Power and voltage compatibility
Cable management and termination quality
Compliance with local safety standards

Sub categories

Showing Results for Accessories

Compare

Out of stock
Ubiquiti

SKU: UACC-DOME-FM-W

Ubiquiti UACC-DOME-FM-W Dome camera mounting accessory, recessed

Recessed dome mount for clean wall and ceiling integration
- Flush-mount design eliminates surface protrusion for seamless installation
- White finish compatible with Ubiquiti dome camera models
- Supports both wall and ceiling mounting configurations
Special Order · Ships in 2-3 weeks

$40.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-DOME-WS-B

Ubiquiti UACC-DOME-WS-B Dome Camera Weather Shield

Weather shield dome for Ubiquiti outdoor cameras; reduces glare and lens contamination
- Transparent dome design preserves native focal length and full field of view
- Shields lens from rain, dust, and particulates to maintain image contrast year-round
- Reduces sun glare and heat shimmer distortion in high-contrast outdoor scenes
In stock · Ships same business day

$147.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-DOME-WS-W

Ubiquiti UACC-DOME-WS-W Dome Camera Mounting Accessory

Weather-sealed white dome enclosure for wall and pole camera mounts
- Rain, snow, and moisture protection extends outdoor camera lifespan
- White UV-stable finish reduces solar heat absorption in direct sun
- Compatible with Ubiquiti dome camera systems; wall and pole mounting
In stock · Ships same business day

$29.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-DOORCLOSER

Ubiquiti UACC-DOORCLOSER Mechanical Door Closer

Spring-loaded mechanical door closer, no power required
- Closes doors independently via spring tension during power loss or system downtime
- Hydraulic damping over final 60 degrees prevents slamming and hardware wear
- Zero calibration or seasonal maintenance; integrates with Ubiquiti access control
In stock · Ships same business day

$184.00 $136.99 Save $47.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-DUAL-POWER-INJECTOR

Ubiquiti UACC-DUAL-POWER-INJECTOR Dual PoE Injector

Dual 2.5G PoE injector with 100W for outdoor Wave deployments
- Two 2.5 Gigabit PoE ports deliver 100W total across both endpoints
- 48V passive PoE powers compatible Ubiquiti Wave series access points
- Weatherproof enclosure with included pole and wall-mount hardware
In stock · Ships same business day

$123.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-ETH-SP-DIN

Ubiquiti UACC-ETH-SP-DIN Bidirectional Ethernet Surge Protector

Inline Ethernet surge protection with 20kA handling and 10 Gbps pass-through
- 20kA impulse discharge rating absorbs lightning and power surge transients
- 10 Gbps data rate with full PoE++ pass-through for powered devices
- DIN rail and wall-mount form factor fits standard network cabinet installations
In stock · Ships same business day

$30.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-ETH-SP-PANEL-24

Ubiquiti UACC-ETH-SP-PANEL-24 Rack-Mount Surge Protection Panel

48-port rack panel with 20kA surge protection and full PoE++ passthrough
- 48 RJ45 ports each rated 20kA surge discharge for lightning and ESD events
- Passes full PoE++ power (up to 95W per port) with zero voltage drop
- 1U form factor, 10 Gbps data rate, operates −40°C to +80°C
In stock · Ships same business day

$421.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-ETH-SP-PRO

Ubiquiti UACC-ETH-SP-PRO Outdoor Ethernet Surge Protector

Dual-port Ethernet surge protection for outdoor PoE networks up to 10 Gbps
- 20 kA discharge capacity absorbs lightning-induced transients on aerial runs
- Passes 802.3af/at and passive PoE without signal loss or voltage degradation
- IPX5 spray-resistant polycarbonate enclosure rated −30°C to +65°C operation
In stock · Ships same business day

$31.00 $17.99 Save $13.01

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-EV-STATION-STAND

Ubiquiti UACC-EV-STATION-STAND stand to mount up to two EV

Vertical stand for up to two Ubiquiti EV Stations indoors or out
- SUS304 stainless steel construction resists corrosion in outdoor use
- Compact 208 x 95 x 1277 mm footprint fits space-constrained sites
- 18 kg weight supports stable, permanent mounting of dual chargers
Special Order · Ships in 2-3 weeks

$580.00 $421.99 Save $158.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-FIBER-SR-KIT

Ubiquiti UACC-FIBER-SR-KIT Fiber Strain Relief Kit

UV-stabilized fiber strain relief kit for pole or wall mounting
- UV-stabilized polycarbonate enclosure rated to -10–60°C and 95% humidity
- Withstands 200 km/hr winds; stabilizes reel under load on towers or poles
- Detachable reel organizes fiber loops and protects connections from weather
In stock · Ships same business day

$55.59 $22.99 Save $32.60

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-FLEX-CAM-PWM-BLACK

Ubiquiti UACC-FLEX-CAM-PWM-BLACK Wall or pole mount for G3

Weatherproof wall or pole mount for Ubiquiti G3 Flex cameras
- Mounts on walls or poles for flexible placement without permanent modifications
- Weatherproof construction rated for outdoor and transitional environments
- Compatible with G3 Flex and G5 Flex camera models
In stock · Ships same business day

$30.95 $13.99 Save $16.96

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-FLEX-CAM-PWM-WHITE

Ubiquiti UACC-FLEX-CAM-PWM-WHITE Wall or pole mount f/ G3/G5

Weatherproof wall/pole mount for Ubiquiti G3 & G5 Flex cameras
- Compatible with G3 Flex and G5 Flex camera models for standardized deployments
- Wall or pole mounting options for flexible outdoor positioning and installation
- Weatherproof construction rated for outdoor and exposed environments
Special Order · Ships in 2-3 weeks

$13.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-FLEX-CAM-PWM-BLACK-3

Ubiquiti UACC-FLEX-CAM-PWM-BLACK-3 wall or pole mount for G3

Wall and pole mount for Ubiquiti G3 Flex cameras, outdoor-rated
- Weatherproof design supports both wall and pole installation options
- Lightweight at 0.2 lb for easy handling and quick deployment
- Compatible with G3 and G5 Flex camera models for flexible placement
In stock · Ships same business day

$72.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-FLEX-CAM-PWM-WHITE-3

Ubiquiti UACC-FLEX-CAM-PWM-WHITE-3 Wall/Pole Mount

Weatherproof wall/pole mount for Ubiquiti G3 & G5 Flex cameras
- Dual wall and pole mounting configurations adapt to any outdoor installation
- Weatherproof rated with corrosion-resistant hardware for exposed environments
- White powder coat finish blends seamlessly with light building facades
In stock · Ships same business day

$190.99

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-FLEX-UTILITY-PRO

Ubiquiti UACC-FLEX-UTILITY-PRO universal outdoor weatherproof

IPX6 polycarbonate enclosure for outdoor UniFi and UISP gear
- IPX6 weatherproof rating protects equipment from moisture and dust
- Compact 350 x 220 x 89 mm design fits rooftops and cable runs
- Wall and pole-mount hardware included for flexible installation
Special Order · Ships in 2-3 weeks

$97.87 $63.99 Save $33.88

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-FM

Ubiquiti UACC-FM magnetic wall mount

Compact magnetic wall mount for UniFi Express & Gateway Lite
- Three installation methods—screw, anchor, or magnetic—on drywall, concrete, or metal
- Polycarbonate with silicone rubber housing for clean, stable positioning
- Floating bracket design fits UniFi Express (UX) and UXG-Lite devices
Special Order · Ships in 2-3 weeks

$53.99

Add to Cart
The item has been added

What to Look For When Buying

The six decisions that matter most before you spec.

Match Bracket to Camera + Surface

A dome camera mounted on a textured wall needs a wall-mount adapter with a gasket; mounted on a pole it needs a pole-mount arm; mounted on an eave it may need a pendant. Third-party brackets exist but brand-specific brackets include proper camera cable routing and weather gasketing. Buying a $40 generic bracket to save on a $80 Axis bracket usually costs more in installation time.

Enclosure NEMA Rating

NEMA 3R = light rain; NEMA 4 = splash + driving rain; NEMA 4X = above + corrosion resistance (coastal, industrial); NEMA 6 = temporary submersion. For weather-exposed camera enclosures, NEMA 4X is the commercial standard. For mission-critical outdoor gear, pair NEMA 4X enclosure + IP67 camera + IK10 vandal rating.

C/CS-Mount Lens Selection

Box cameras use interchangeable C-mount (17.526mm flange) or CS-mount (12.5mm flange). Lens focal length + sensor size determines field of view: a 4mm lens on a 1/3" sensor gives ~60° horizontal FOV. Our DORI guide covers lens selection by scene distance. F-stop matters for low-light; P-iris for auto-exposure.

IR Illuminator Wavelength

850nm IR is more efficient but produces a faint visible red glow (deterrent or accidental giveaway, depending on use case). 940nm is truly covert but requires ~2x the power for the same effective range, and many cameras have lower sensitivity at 940nm. Match illuminator wavelength to camera IR-cut filter spec, or image washout results.

Power Supply Sizing & Distance

12VDC cameras at 100ft from a power supply drop significant voltage over 18-gauge wire — a camera rated for 12V may see 10.5V at the camera end under load, triggering brownout resets. For long runs, use a higher-voltage power supply (24VAC or 48VDC) and step down at the camera. UL-listed surveillance power supplies (Altronix) publish voltage-drop tables.

Cable Jacket Rating

Indoor Cat6 is rated CM (communications); plenum-rated CMP is required for above-drop-ceiling runs per NFPA 70. Outdoor/direct-burial Ethernet is a different product (CMX, direct-burial gel-filled). Mixing jacket ratings causes code violations and fire inspector rejections. Always spec by run environment, not lowest-cost SKU.

Technology Stack

The specs and acronyms that actually affect outdoor performance.

NEMA vs IP Rating Systems

NEMA is the US enclosure standard (NEMA 1-13); IP is the international standard (IP00-IP68). Rough crosswalk: NEMA 4 ≈ IP66, NEMA 4X ≈ IP66 + corrosion, NEMA 6 ≈ IP67. Some spec sheets list both; when only one is given, the crosswalk is approximate. For coastal, industrial, and food-processing environments, specify NEMA 4X or IP66 + stainless steel.

C-Mount vs CS-Mount Lenses

C-mount: 17.526mm flange focal distance. CS-mount: 12.5mm flange. CS cameras accept both lens types (C lenses need a 5mm adapter ring); C cameras accept only C lenses. Most modern box cameras are CS-mount for lens flexibility. Lens thread is 1-inch × 32 TPI on both.

F-Stop / Iris

F-stop = focal length ÷ aperture diameter. Lower F-stop (wider aperture) means more light, better low-light performance, shallower depth of field. F1.4 is very low-light capable; F1.8 is common commercial spec. P-iris (precise iris) lenses auto-adjust aperture based on scene lighting — reduces over-exposure during day, improves low-light at night.

850nm vs 940nm IR

IR illuminators at 850nm are more energy-efficient and the sensitivity of most camera IR-cut filters peaks here — but 850nm produces a faint visible red glow from the LEDs. 940nm is invisible to human eye but requires ~2x the power or shorter effective range. Many covert-deployment cameras are re-tuned for 940nm sensitivity.

UL-Listed Power Supplies

Underwriters Laboratories listed power supplies meet safety standards for overcurrent, overvoltage, and enclosure isolation. UL 294 specifies additional requirements for access control; UL 603 for security burglary; UL 1310 for Class 2 power. Insurance and code requirements increasingly specify UL-listed supplies — particularly in commercial and institutional installations.

Plenum vs Riser vs PVC Cable

Plenum-rated (CMP) cable uses low-smoke FEP jacket for use above suspended ceilings where smoke spreads through return-air plenums. Riser (CMR) is for vertical shaft runs between floors. PVC (CM) is for open office runs only. Using CM in plenum spaces violates NFPA 70 — costly inspector rejection if caught.

Typical Deployment Scenarios

New Construction Retrofit

Cat6A plenum cable pulled to camera locations with proper service loops, 2-gang electrical boxes at each dome location with weatherproof backbox, Cat6A patch panel at the IDF, UL-listed power supplies for any 12V/24V camera, labeled and tested before cameras are mounted.

Coastal / Corrosive Environment

NEMA 4X stainless-steel enclosures for outdoor cameras, 316-grade stainless brackets, silicone dielectric grease on every connector, hot-dipped galvanized or powder-coated steel poles. Budget 15-25% more on accessories vs. standard outdoor — and plan for 3-5 year inspection cycles rather than 10.

Box-Camera LPR Application

Box camera with 50-150mm telephoto lens, dedicated 850nm IR illuminator at same height as camera, pole-mount bracket with junction box, UL power supply for camera + illuminator. LPR-specific enclosures with anti-reflective glass to avoid nighttime IR bloom. Typical deployment: dedicated lane camera, not general-purpose surveillance.

Parking Garage Retrofit

Existing analog coax cable replaced via NVT Phybridge or similar PoE-over-coax, vandal-resistant dome enclosures at ground level, low-profile bullet cameras on ceiling, LED-plus-IR-compatible illuminators to handle harsh fluorescent lighting. Enclosures rated for vehicle-exhaust environment.

Frequently Asked Questions

Do I need the OEM bracket for my camera, or will a generic bracket work?

For most commercial installations, specify the OEM bracket. Brand-specific brackets include proper cable routing, gasketed weather seals, and mounting-hole patterns matched to the camera — which matters more than the cost savings of a generic bracket. Generic brackets are acceptable for indoor standard-dome cameras on flat surfaces; for outdoor, vandal-rated, or pendant applications, use OEM.

What NEMA rating do I need for outdoor camera enclosures?

NEMA 4 for most weather-exposed deployments (driving rain, snow). NEMA 4X for coastal, industrial, or food-processing environments (adds corrosion resistance — typically stainless steel or fiberglass construction). NEMA 6 for temporary submersion or flood-prone areas. The IP-rating equivalent is IP66 for NEMA 4, IP66 + corrosion for NEMA 4X, IP67 for NEMA 6.

How do I choose the right lens focal length for a box camera?

Work backward from the scene. Identify the farthest point you need identification-grade coverage, use our DORI guide to calculate required pixels-per-foot at that distance, and match lens focal length + sensor size to deliver that PPF. A 4mm lens on a 1/3" sensor covers ~60° horizontal FOV; a 12mm lens on the same sensor covers ~20°. Wide FOV = shorter identification distance.

What's the difference between 850nm and 940nm IR illuminators?

850nm is more energy-efficient — you get more effective range per watt — but produces a faint visible red glow from the LEDs. 940nm is truly invisible to the human eye but requires about 2x the power for equivalent range, and many cameras have lower sensor sensitivity at 940nm. For deterrent visibility or cost-efficient long-range, 850nm; for covert applications, 940nm.

Can I power an IP camera with a generic 12V wall-wart?

Not for a commercial deployment. Generic wall-warts are unregulated, not UL-listed for security applications, and typically don't include surge protection. Use a UL-listed surveillance power supply (Altronix AL series, UL 294 or UL 603) with battery backup where required. PoE is preferred when possible — single cable, centralized power management, UPS-backed.

What cable jacket rating do I need for in-ceiling runs?

Plenum-rated (CMP) cable is required for any run through a return-air plenum space above suspended ceilings (most commercial buildings). Riser (CMR) for vertical shafts between floors. PVC (CM) for open office spaces only. Using non-plenum cable in a plenum space is a fire-code violation under NFPA 70 and will be rejected by inspectors. Budget plenum cable for any building where you're not 100% sure of the return-air path.

Accessories

Deployment Considerations

Sub categories

Showing Results for Accessories

Ubiquiti UACC-DOME-FM-W Dome camera mounting accessory, recessed

Ubiquiti UACC-DOME-WS-B Dome Camera Weather Shield

Ubiquiti UACC-DOME-WS-W Dome Camera Mounting Accessory

Ubiquiti UACC-DOORCLOSER Mechanical Door Closer

Ubiquiti UACC-DUAL-POWER-INJECTOR Dual PoE Injector

Ubiquiti UACC-ETH-SP-DIN Bidirectional Ethernet Surge Protector

Ubiquiti UACC-ETH-SP-PANEL-24 Rack-Mount Surge Protection Panel

Ubiquiti UACC-ETH-SP-PRO Outdoor Ethernet Surge Protector

Ubiquiti UACC-EV-STATION-STAND stand to mount up to two EV

Ubiquiti UACC-FIBER-SR-KIT Fiber Strain Relief Kit

Ubiquiti UACC-FLEX-CAM-PWM-BLACK Wall or pole mount for G3

Ubiquiti UACC-FLEX-CAM-PWM-WHITE Wall or pole mount f/ G3/G5

Ubiquiti UACC-FLEX-CAM-PWM-BLACK-3 wall or pole mount for G3

Ubiquiti UACC-FLEX-CAM-PWM-WHITE-3 Wall/Pole Mount

Ubiquiti UACC-FLEX-UTILITY-PRO universal outdoor weatherproof

Ubiquiti UACC-FM magnetic wall mount

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Outdoor Deployments

Frequently Asked Questions

Related Categories

Engineering Reading