Bosch 60W IEEE 802.3BT SINGLE PORT 100-240VAC INPUT OUTDOOR. TAA COMPLIANT - NPD-6001C-EBT

Bosch NPD-6001C-EBT 60W IEEE 802.3bt Single-Port Outdoor PoE Injector

Overview

The Bosch NPD-6001C-EBT is a 60W IEEE 802.3bt Type 3 single-port outdoor PoE injector built for installations where the switch is indoors but the powered device — a PTZ camera, multi-sensor, or high-draw access control reader — sits outside in weather that would kill lesser hardware. It accepts 100–240 VAC worldwide input, delivers 54 VDC at up to 60W to the field device, and carries an IP67 enclosure rating, NEMA 4X designation, and ASTM B-117 corrosion resistance certification. If you're running a high-wattage outdoor camera or access device off a standard 802.3at switch, this injector bridges the power gap while surviving the environment.

The NPD-6001C-EBT (often searched as NPD 6001C EBT) is TAA compliant, making it eligible for federal, state, and education projects subject to the Trade Agreements Act.

Key Features

• 60W IEEE 802.3bt Type 3 PoE Output: Delivers the full 60W that 802.3bt Type 3 permits at the port — enough to run current-generation multi-sensor panoramic cameras, high-zoom PTZs, or thermal imagers that exceed the 30W ceiling of 802.3at. If your camera spec sheet calls for more than 25.5W, this is the class of injector you need.
• IP67 + NEMA 4X Enclosure: IP67 means the unit survives temporary submersion up to 1 meter — not just rain splash. NEMA 4X adds corrosion resistance suitable for coastal, chemical, or wash-down environments. Deploy it in a junction box or directly in the field without a secondary weatherproof enclosure in most outdoor scenarios.
• ASTM B-117 Salt-Fog Corrosion Resistance: Tested to the ASTM B-117 standard — the same salt-spray test used for automotive and marine hardware. Relevant for coastal perimeter installations, port facilities, or any site where airborne chlorides are a long-term threat to electronics.
• -40°C to 65°C Operating Range: That's -40°F to 149°F — a genuine cold-climate and high-heat rating. Northern outdoor deployments that see extreme winter lows won't require enclosure heaters, and high-ambient industrial rooftop installs stay within spec through summer peaks.
• 100–240 VAC Universal Input: The injector accepts any standard AC supply worldwide at 50–60 Hz, drawing up to 2A. No transformer or line-matching needed for international projects; a single SKU covers North American and European power infrastructure.
• 10/100/1000 Mbps Data Pass-Through: Full gigabit data rates pass through alongside power on the shielded RJ-45 port. High-bitrate 4K or multi-stream cameras won't hit a bandwidth bottleneck at the injector — the data path is not the constraint.
• Surge Protection to GR-1089-CORE Issue 4 and ITU-T K.21: These are telecom-grade surge standards — GR-1089 is required for equipment connected to outside plant in carrier networks, and ITU-T K.21 covers lightning and switching surge protection. For cameras on poles, rooftops, or long outdoor cable runs where lightning-induced surges are a real failure mode, this level of surge hardening matters.
• 200,000-Hour MTBF at 25°C: Over 22 years of calculated mean time between failures under standard operating conditions. For infrastructure that lives in a junction box on a pole and is expected to run maintenance-free, that reliability figure is the relevant comparison point when evaluating total cost of ownership.
• PoE Pin Assignment — Mode A and Mode B: Output polarity is 4/5(+), 7/8(-), 1/2(-), 3/6(+), supporting both pin assignment modes. This ensures compatibility with the broad range of 802.3bt-capable cameras and devices without requiring manual configuration.

Integration and Compatibility

The NPD-6001C-EBT is designed to extend power to any IEEE 802.3bt Type 3 compliant device — PTZ cameras, multi-sensor panoramic cameras, thermal imaging units, or access control hardware drawing up to 60W. It connects upstream to any standard AC power source and downstream via shielded RJ-45 to the field device. Regulatory compliance covers IEEE 802.3bt Type 3, RoHS, WEEE, and CE, alongside FCC Part 15 Class B and EN 55032 Class B electromagnetic emission standards — the unit is appropriate for both North American and European deployments. Safety certification to UL/IEC/EN 60950-1 and UL 60950-22 covers both indoor and outdoor-rated equipment. TAA compliance makes this a valid selection for U.S. government contracts and procurement vehicles that require domestic-origin sourcing.

Physical installation fits a wide range of junction box sizes: the unit measures 60 mm × 140 mm × 170 mm (2.36 in × 5.51 in × 6.69 in) and weighs 1,400 g (3.08 lb). Maximum operating altitude of 2,000 m (6,560 ft) covers the vast majority of high-elevation outdoor deployments. For a broader view of the Bosch surveillance line, including cameras and video management systems that pair with this injector, see the full catalog. If you're planning a multi-camera outdoor PoE injector deployment, check our PoE planning guide for budget and cable-length calculations. High-wattage PTZ and multi-sensor cameras that typically require 802.3bt power are covered in the PTZ camera category. Pairing this injector with a compatible managed PoE switch upstream allows centralized monitoring of the AC-side power feed.

Frequently Asked Questions

Q: Is the NPD-6001C-EBT TAA compliant?

A: Yes. The NPD-6001C-EBT carries explicit TAA compliance, making it eligible for federal, state, and education procurement vehicles subject to the Trade Agreements Act.

Q: What is the maximum PoE output power of the NPD-6001C-EBT?

A: The NPD-6001C-EBT delivers up to 60W at 54 VDC on its single port, per the IEEE 802.3bt Type 3 standard. This covers high-draw devices such as multi-sensor panoramic cameras, high-zoom PTZs, and thermal imagers that exceed the 30W limit of 802.3at injectors.

Q: Can the NPD-6001C-EBT be mounted outdoors without an additional weatherproof enclosure?

A: The unit is rated IP67 (temporary submersion to 1 meter) and NEMA 4X (corrosion-resistant), so it can be installed in most exposed outdoor locations without a secondary enclosure. For wash-down environments or sites with sustained water exposure, verify your specific installation conditions against the IP67 rating.

Q: What AC input voltage does the NPD-6001C-EBT accept?

A: It accepts 100–240 VAC (±10%) at 50–60 Hz, drawing up to 2A. A single unit works on both North American and European mains power without any additional transformer or step-down equipment.

Q: What are the operating temperature limits for the NPD-6001C-EBT?

A: Operating range is -40°C to 65°C (-40°F to 149°F). This covers extreme cold-climate outdoor deployments without enclosure heating and high-ambient rooftop or industrial installations through summer peak temperatures.

Q: What surge protection standards does the NPD-6001C-EBT meet?

A: The NPD-6001C-EBT is rated to GR-1089-CORE Issue 4 and ITU-T K.21 — telecom-grade surge standards that cover lightning-induced and switching surges. This is relevant for cameras on poles, rooftops, or long outdoor cable runs where transient surges are a known failure mode.

James Everett

The NPD-6001C-EBT is the injector I reach for when a project calls for 802.3bt power at an outdoor node and there's no PoE++ switch budget or rack space at the pole location. The 200,000-hour MTBF at 25°C is the spec that makes this viable as a set-and-forget install — in a junction box on a camera pole, you realistically cannot budget annual service visits, and that MTBF number translates to calculated reliability over the system lifecycle.

Technical Highlights:

• 60W / 54 VDC Output: Full 802.3bt Type 3 budget at the port — covers every current-generation high-draw outdoor camera on the market, with margin for future device upgrades without replacing the injector.
• GR-1089-CORE + ITU-T K.21 Surge Rating: Telecom-grade protection on both the data and power lines. For pole-mounted or rooftop installs where lightning coupling on long cable runs is a real exposure, this is the spec that differentiates a $400 service call from a failed port on a cheap injector.
• IP67 + NEMA 4X + ASTM B-117: Three independent certifications covering submersion, corrosion, and salt-fog — not just a single IP rating. The ASTM B-117 salt-spray test is the one that matters for coastal perimeter and port security deployments where sea air attacks hardware over a 5-to-10-year horizon.

Deployment Considerations:

• The unit draws up to 2A at 100–240 VAC — verify your junction box circuit breaker and conduit fill are sized for this before commissioning. At 100 VAC input the draw hits the 2A ceiling; at 240 VAC it drops proportionally, but the circuit protection design should assume worst-case.
• Maximum operating altitude is 2,000 m (6,560 ft). If you're deploying at high-elevation mountain sites above that threshold — ski resort perimeter, communications tower infrastructure — this unit is out of spec and you'll need a different solution.

This injector is the right fit for coastal port perimeter, border infrastructure, and industrial outdoor surveillance nodes where a PTZ or multi-sensor camera requires 802.3bt power, the environment is genuinely hostile, and the device needs to run without intervention for years. It is not the economical choice for a 15W indoor dome.