Panduit UTP28X25GR 28 AWG Cat 6A UTP Patch Cord 25ft Green

Panduit UTP28X25GR Pan-Net Cat 6A 28 AWG UTP Patch Cord, 25 ft, Green

The Panduit UTP28X25GR is a 25-foot Cat 6A UTP patch cord engineered for high-density data center and enterprise network deployments where airflow, cable management, and full 10GBASE-T performance must coexist. Built with 28 AWG solid copper conductors instead of traditional 23-24 AWG cable, this cord delivers a 0.185-inch (4.7 mm) outside diameter—roughly 40% thinner than standard patch cords—while maintaining full ANSI/TIA-568.2-D Category 6A performance to 500 MHz. For IT teams managing congested server racks, top-of-rack switch patching, or SAN fabric connections, the reduced bundle diameter translates directly to improved cooling efficiency and faster MACs (moves, adds, changes). The green jacket provides instant visual identification in mixed-protocol environments, and the patented tangle-free latch prevents snags during extraction—eliminating the common failure mode where traditional latches catch on adjacent cables and break mid-pull.

Key Features

• 28 AWG Slim Profile: 0.185" diameter enables 6:1 pathway fill ratio vs. standard cords; reduces airflow blockage in high-density racks by up to 35%
• Full 10GBASE-T Certification: 100% factory tested for wire map, NEXT, and return loss; exceeds Cat 6A channel specs 1–500 MHz with centered de-embedded plug design
• PoE++ Ready: Supports IEEE 802.3bt Type 3 and Type 4 (up to 90W per port) for powering Wi-Fi 6E APs, PTZ cameras, and PoE lighting without voltage drop
• Tangle-Free Latch: Panduit's patented low-profile latch prevents cable snags during extraction; 40% faster disconnect time in blind-reach scenarios vs. standard boots
• RapidID Integration: Pre-applied barcode labels enable instant port mapping and asset tracking via Panduit's RapidID mobile app—eliminates manual documentation errors
• CM/LSZH Rated: Low-smoke zero-halogen jacket meets IBC and IFC requirements for data center raised-floor installations; reduced toxicity during fire events

The UTP28X25GR's solid 28 AWG copper conductors are specified for permanent link applications, not stranded patch cord use—this construction provides lower DC resistance (19.2Ω per 100m vs. 23.5Ω for stranded 28 AWG) and better high-frequency performance stability across temperature swings common in HVAC-cycled data centers. The centered pair geometry inside each RJ45 plug maintains 35+ dB NEXT margin at 500 MHz, and the integral pair manager inside the plug boot prevents conductor untwisting beyond the 0.5-inch detach point mandated by ANSI/TIA-568.2-D Annex G. Every cord ships with test reports traceable to NIST standards, showing insertion loss, return loss, and crosstalk measurements across all four pairs—critical documentation for TIA-942 data center audits or BICSI RCDD certification submittals. The green jacket color follows TIA-606-B identification standards for crossover or dedicated network segments, though the cord is wired straight-through (compatible with both T568A and T568B host equipment).

In deployment, the 28 AWG form factor solves the airflow crisis in 42U racks running 10G spine-leaf fabrics: a 48-port 1U switch patched with standard Cat 6A cords creates a 4-inch bundle in the vertical cable manager that blocks 60–70% of front-to-back airflow, forcing hot-aisle temps 8–12°F higher than design and triggering nuisance thermal shutdowns on lower-U equipment. Swapping to UTP28X series cords cuts bundle diameter in half, restores airflow to within 15% of empty-rack baseline, and allows IT teams to defer expensive hot-aisle containment retrofits. The tangle-free latch becomes critical in lights-out remote-hands scenarios—when a NOC tech is running MACs via video call at 2AM, a single broken latch tab can turn a 10-minute port move into a 40-minute truck roll for replacement cord procurement. Panduit's latch design uses a reinforced TPE overmold that flexes under side load instead of fracturing, tested to 750 insertion cycles vs. the 200-cycle TIA minimum.

The UTP28X25GR is factory-terminated and certified to exceed ANSI/TIA-568.2-D Category 6A, ISO/IEC 11801 Class EA, and IEC 60603-7-51 performance requirements. It meets UL 1863 and CSA C22.2 safety standards (UL File E129886), complies with FCC Part 68 (now ANSI/TIA-1096-A) for telecom attachment, and is RoHS-compliant for EU installations. The 25-foot length suits typical rack-to-rack adjacency or same-row server-to-switch patching in hot-aisle/cold-aisle layouts; for intra-rack connections, consider Panduit's 3ft–7ft variants to eliminate service loop clutter. Each cord includes pre-applied RapidID barcode labels on both plug boots for instant scanning with Panduit's mobile port-mapping app—eliminating the manual spreadsheet reconciliation that causes 15–20% of all Tier-1 trouble tickets in large data centers. The Pan-Net sub-brand designates Panduit's contractor-grade structured cabling line, balancing performance and cost for projects where 25-year warranty isn't required but TIA compliance is non-negotiable.