Altronix WAYPOINT1012V 12VDC 10A Outdoor Power Supply/Charger
Overview
The Altronix WAYPOINT1012V is a 12VDC, 10A continuous outdoor power supply and battery charger built for security installations that need a reliable, weatherproof power source at the point of use — rather than running long cable runs back to an interior IDF or equipment room. The molded fiberglass reinforced polyester enclosure carries a NEMA 4/4X, IP66-11 rating, which means it handles rain, dust, hose-directed water, and corrosive environments without issue. If you're powering perimeter cameras, gate controllers, or access readers on an exterior wall or pole, the Altronix power supply line — and this unit specifically — is purpose-built for that scenario.
Input is 230VAC, 50/60Hz at 3A, making the WAYPOINT1012V the correct choice for international deployments and sites wired for European-standard mains voltage. The filtered and electronically regulated output holds a clean 12VDC regardless of load swings — critical when you're powering cameras with IR illuminators or motorized lenses that draw variable current.
Key Features
- 10A Continuous Output at 12VDC: delivers enough capacity for multiple downstream 12V devices simultaneously — typical IP cameras with IR draw 1–3A each, so this supply can support three to five cameras on a single outdoor enclosure without derating.
- NEMA 4/4X, IP66-11 Enclosure: the fiberglass reinforced polyester housing resists rain, dust, and corrosive atmospheres. NEMA 4X specifically covers corrosion resistance, making this suitable for coastal, industrial, or chemical-adjacent environments where a standard NEMA 4 steel box would rust through in a season.
- Dual Internal Battery Capacity (2 × 12VDC/7AH): the enclosure accommodates up to two 7AH sealed lead-acid or gel batteries inside — no separate battery cabinet needed for basic standby. Upon AC loss, failover is instantaneous. For longer hold times, external batteries up to 40AH or 65AH can be added in a separate ventilated enclosure.
- 230VAC / 50/60Hz Input: wired for international mains voltage, not the 120VAC standard in North America. This is the right unit for international projects, or domestic sites with 208–240V single-phase circuits already available at the mounting location.
- Thermal Overload and Short Circuit Protection: onboard protection prevents damage to both the supply and downstream devices if a wiring fault or overload condition occurs — reduces service calls on remote outdoor installations where a failed unprotected supply would otherwise require a truck roll.
- AC and DC Power LED Indicators: visible status LEDs for both AC presence and DC output mean a technician can confirm the supply is live and producing output without opening the enclosure or breaking out a meter — saves time during commissioning and troubleshooting.
- Lockable Stainless Steel Latches: tamper resistance matters on exterior installations; the stainless latches support a padlock (Altronix LOCK1WP, sold separately) to deter unauthorized access to the wiring compartment.
- Integral Flanges for Wall or Pole Mounting: built-in mounting flanges simplify installation on flat surfaces; the optional PMK1 pole mount kit extends placement to pipes and poles without field-fabricated brackets.
- Wide Operating Temperature Range (-40°C to 60°C): this range covers essentially any outdoor installation from arctic perimeter fencing to sun-baked rooftop deployments in hot climates — if your site sees -40°F winters or 140°F direct-sun enclosure temperatures, this unit stays in spec.
- NDAA, TAA, BAA, and CE Compliant: the NDAA Section 889 compliance designation means this supply can be used on federal, state, and municipal government projects where Chinese-origin components are restricted. TAA compliance covers GSA contract procurement. CE marks the unit for European deployment.
Integration and Compatibility
The WAYPOINT1012V is designed as a distributed outdoor power supply node in larger surveillance and access control architectures. It pairs naturally with 12VDC cameras, access control panels, gate operators, and intercoms that run on 12V. For integrators designing a perimeter IP camera deployment, placing this unit at the pole or wall where cameras mount eliminates the voltage-drop problem that plagues long 12V cable runs — at 10A over long distances, even 18AWG wire introduces meaningful drop that affects IR illuminator performance and camera stability.
The WG1 NEMA-rated wire gland inlets (sold separately) allow clean, weatherproof cable entry without compromising the enclosure rating — important to maintain the IP66 rating after field wiring. For access control systems requiring backup power at the door, this enclosure's battery charging circuit handles sealed lead-acid and gel-type batteries, covering most door controller power requirements.
Integrators looking at PoE-based camera deployments should note this is a straight 12VDC supply, not a PoE injector — it pairs with 12VDC-native devices or analog cameras. For PoE camera runs, pair with an appropriate outdoor PoE switch instead.
Frequently Asked Questions
Q: Is the WAYPOINT1012V NDAA Section 889 compliant?
A: Yes. The WAYPOINT1012V carries NDAA compliance as listed in Altronix's agency listings, making it eligible for federal, state, and municipal projects subject to Section 889 component restrictions.
Q: Does the WAYPOINT1012V include batteries?
A: No. Batteries are sold separately. The enclosure accommodates up to two 12VDC/7AH sealed lead-acid or gel-type batteries internally. For extended standby, external battery enclosures supporting up to 40AH or 65AH can be added.
Q: What input voltage does the WAYPOINT1012V require?
A: The WAYPOINT1012V requires 230VAC, 50/60Hz at 3A. This is not a dual-voltage unit — it is wired for 230VAC only, not 120VAC. Verify your available mains voltage before ordering.
Q: Can the WAYPOINT1012V be pole-mounted?
A: Yes, with the optional Altronix PMK1 Pole Mount Kit. The enclosure also includes integral flanges for direct wall mounting without additional hardware.
Q: What is the warranty on the WAYPOINT1012V?
A: Altronix covers the WAYPOINT1012V under their lifetime warranty, as stated on the product page.
Q: What enclosure rating does the WAYPOINT1012V carry, and is it suitable for coastal or industrial environments?
A: The enclosure is rated NEMA 4/4X and IP66-11. NEMA 4X includes corrosion resistance, making it appropriate for coastal, chemical-adjacent, and industrial outdoor environments where corrosion is a concern.
The WAYPOINT1012V is the unit I specify when a project calls for distributed outdoor power at 230VAC sites — the -40°C to 60°C operating range and NEMA 4X corrosion-resistant enclosure handle conditions that would kill a standard indoor supply within a year. At 10A continuous output, you have real headroom for multi-device loads at the pole without separate junction boxes or parallel supplies.
Technical Highlights:
- Instantaneous AC Failover: upon mains loss, the supply switches to battery without any dropout — no camera reboot, no access controller reset. With two 7AH batteries internal, that's meaningful hold time for single-door or two-camera nodes.
- NEMA 4X Fiberglass Enclosure: the molded fiberglass reinforced polyester construction is non-corroding by design — not painted steel that chips and rusts. On a coastal perimeter or a wastewater facility fence line, this is the material choice that survives a five-year maintenance cycle.
- Filtered and Regulated 12VDC Output: electronically regulated output means voltage doesn't sag under load — relevant when IR illuminators on cameras draw their peak current at night and you need the 12V rail to stay stable for reliable operation.
Deployment Considerations:
- This unit is 230VAC input only — confirm your site has 230V single-phase available at the mounting location before specifying. North American 120VAC sites need a different SKU in the WayPoint family.
- Batteries are not included and must be ordered separately; the enclosure holds up to two 12VDC/7AH units. If your standby requirement exceeds 14AH, plan for an external ventilated battery enclosure — the internal cavity is the limiting factor, not the charger circuit itself.
This supply fits cleanly into international perimeter camera deployments, outdoor access control nodes at gate pedestals, and any application where you need a UL-listed, NDAA-compliant power source mounted at the device location rather than run back to a conditioned interior space.
