STI

STI

SKU: BPF2016

STI BPF2016 EnviroArmour Fiberglass Back Panel 20x16

• Fiberglass substrate resists weather and mechanical stress at exterior door installations.
• 20×16-inch panel consolidates EM locks, mag strikes, and readers on one rigid surface.
• Supports 9VDC strike hardware and card, keypad, or biometric reader mounting.

STI

SKU: BPF1816

STI EnviroArmour® Fiberglass Back Panel - 18" x 16" - BPF1816

• Fiberglass construction resists corrosion, UV, and moisture where steel panels fail.
• 18" × 16" form factor fits standard single-gang and dual-gang enclosure footprints.
• Outdoor-rated substrate supports exterior reader and strike assembly mounting at 9VDC.

STI

SKU: BPF1614

STI BPF1614 EnviroArmour Fiberglass Back Panel 16x14

• Fiberglass construction resists salt spray, UV, and corrosion in outdoor installations.
• Supports 9VDC powered strikes without flex or crack propagation under repeated impact.
• Four M8 fixing holes enable secure mounting in surface or recessed door frame configs.

STI

SKU: BPF1412

STI BPF1412 EnviroArmour Fiberglass Back Panel 14x12

• Fiberglass construction resists moisture, UV, and corrosion in outdoor deployments.
• 14×12-inch panel accommodates readers, keypads, and strike assemblies without custom fab.
• Operates at 9VDC, compatible with standard access control power supplies and controllers.

STI

SKU: BPF1210

STI BPF1210 EnviroArmour Fiberglass Back Panel 12x10

• Fiberglass construction resists salt spray, UV, and moisture for outdoor deployments.
• Pre-drilled four-hole pattern fits standard electrical boxes and door frame cavities.
• Rated for 9VDC hardware; supply gasket inserts seal cable entries against water intrusion.

STI

SKU: BPF1008

STI BPF1008 EnviroArmour Fiberglass Back Panel 10x8

10x8 fiberglass back panel shields access control in outdoor/wet conditions

• Weatherproof protection for readers, strike hardware, and cabling outdoors
• Fiberglass construction with environmental sealing resists UV and corrosion
• Mounts behind STI 9VDC access control systems on doors and frames

STI

SKU: BPF0808

STI BPF0808 EnviroArmour Fiberglass Back Panel 8x8

• Fiberglass construction resists moisture, UV, and physical stress in outdoor installs.
• 8×8 inch footprint accommodates standard reader, strike, and control module hardware.
• Four 7mm masonry mount points allow direct wall-templating for fast, repeatable installs.

STI

SKU: BPF0806

STI BPF0806 EnviroArmour Fiberglass Back Panel 8x6

• Fiberglass construction resists UV, moisture, and corrosion in outdoor deployments.
• Non-conductive backing provides electrical isolation where metal enclosures are unsuitable.
• Supports 9VDC electromechanical strikes and standard reader brackets in an 8×6 in. form.

STI

SKU: BPF0606

STI BPF0606 EnviroArmour Fiberglass Back Panel 6x6

• Fiberglass EnviroArmour construction resists corrosion for outdoor-rated deployments.
• 6×6 in. panel provides structural backing for readers, strikes, and credential hardware.
• Four fixing holes accept 7 mm masonry bits for permanent door-frame or surface mounting.

STI

SKU: BPA4836

STI EnviroArmour® Aluminum Back Panel for EN483612-W - BPA4836

• Aluminum construction with EnviroArmour finish resists corrosion in wet and outdoor deployments.
• Purpose-built fit for EN483612-W and EN483612-W2 readers — no field modification required.
• 9VDC operating voltage aligns directly with standard access control panel power architecture.

STI

SKU: BPA2016

STI BPA2016 EnviroArmour Aluminum Back Panel 20x16

• 20×16 in. aluminum panel provides a rigid mounting surface for readers and strike hardware.
• Supports 9VDC access control assemblies including reader card slots and strike driver circuits.
• Rated for outdoor/sheltered environments; frame knockouts allow clean cable routing on install.

STI

SKU: BPA1614

STI BPA1614 EnviroArmour Aluminum Back Panel 16x14

• Aluminum construction resists corrosion in salt-air, coastal, and high-moisture environments.
• 16" × 14" panel provides ample mounting surface for reader heads and strike assemblies.
• 9VDC operation integrates directly with compatible STI EnviroArmour reader and strike systems.

STI

SKU: BPA1412

STI BPA1412 EnviroArmour® Aluminum Back Panel 14x12

• 14×12 in. aluminum surface mounts readers, keypads, and strikes to any door frame.
• Outdoor-rated EnviroArmour® construction resists UV, salt spray, and physical impact.
• Pre-drilled holes and 7mm masonry compatibility simplify concrete and brick installs.

STI

SKU: BPA0808

STI BPA0808 EnviroArmour Aluminum Back Panel 8x8

• Rigid aluminum construction resists corrosion for indoor and outdoor deployments.
• Four 7mm fixing holes provide secure, precise mounting on masonry, steel, or wood.
• Operates at 9VDC and integrates directly with STI lock and strike assemblies.

STI

SKU: BPA0606

STI BPA0606 EnviroArmour Aluminum Back Panel 6x6

• Aluminum construction resists corrosion for reliable outdoor and indoor deployments.
• 6x6 inch form factor matches industry-standard reader and strike hardware cutouts.
• Passive panel requires no dedicated power, simplifying installation and wiring plans.

STI

SKU: BIO-7505

STI Bio Protector - Identification Reader Cover - Smoke Color

Smoke reader cover shields STI biometric keypads from weather

• Weatherproof polymer construction protects outdoor access control readers
• Fits STI keypad-type biometric and identification reader hardware
• 1" thick gasket seals against environmental exposure in high-traffic areas

STI

SKU: STI-PMK1012

STI STI-PMK1012 EnviroArmour Pole Mount Bracket Kit

• Pole mount design supports strike installations on glass doors and wide openings.
• Operates at 9VDC, integrating directly with standard electromagnetic strike systems.
• External pole bracing eliminates surface-mount dependency on door frame geometry.

STI

SKU: STI-PMK0608

STI STI-PMK0608 EnviroArmour® Pole Mount Bracket Kit

• Mounts credential readers to poles ≥2-inch diameter without wall junction boxes.
• Rated for outdoor environments, supporting perimeter and parking lot deployments.
• Operates at 9VDC, integrating with STI access control and compatible third-party readers.

STI

SKU: STI-9767

STI STI-9767 Horn/Strobe Damage Stopper L Series Wall Mount

• Wall-mounted horn and strobe damage stopper cage
• 9-gauge steel wire with corrosion-resistant finish
• Shields signaling devices from vandalism and accidental impact

STI

SKU: STI-9766

STI STI-9766 Horn/Strobe Damage Stopper L Series Wall Mount

Wall mount protective assembly for STI L Series horn/strobe devices

• Gauge-9 steel wire cage with polyester coating resists corrosion and impact damage.
• Includes anchors, fasteners, and template for fast, repeatable wall installations.
• Tool-free removal allows maintenance access without disrupting device operation.