Panduit RAFC10IW-X Surface Raceway Right Angle Fitting
The Panduit RAFC10IW-X right angle fitting routes LD10 and LDPH10 Pan-Way surface raceway around 90-degree corners without kinking cables or violating bend-radius limits. One-piece hinged PVC construction with adhesive backing snaps onto existing raceway runs—no fasteners, no cutting—so you can install clean corner transitions in seconds. Off-white finish matches standard Panduit LD10 profiles. Sold in 10-packs for mid-size retrofit jobs where exposed conduit isn't an option and in-wall fishing would blow the budget.
Key Features
- One-piece hinged design for snap-on installation—no screws or adhesive removal
- Controlled bend radius prevents cable stress and maintains TIA/EIA compliance
- Adhesive backing option for semi-permanent wall mounting at transition points
- 3.18" × 3.18" footprint (80.8 mm) fits LD10 and LDPH10 raceway profiles
- Rigid PVC construction rated UL94V-0 and FT4 for plenum-equivalent fire safety
- Off-white finish coordinates with existing Pan-Way installations
The RAFC10IW-X measures 3.18 inches square with a 0.93-inch profile height (23.6 mm), sized to mate with Panduit's LD10 and LDPH10 surface raceway channels without adapters. The one-piece hinged lid lifts to accept cable bundles, then snaps shut over the raceway joint—no need to pre-thread cables through the fitting. Internal bend geometry maintains a controlled radius that keeps Cat 6A, fiber, and power cables within manufacturer bend-radius specs, critical when you're running PoE++ to cameras or pulling 12-strand OM4 to a floor switch.
Rigid PVC construction carries UL94V-0 and FT4 ratings, meaning it self-extinguishes and produces minimal smoke—important for installations in occupied spaces or near air-handling plenums where local AHJs enforce NFPA 90A interpretations. The adhesive backing secures the fitting to drywall, painted CMU, or cubicle panels without visible fasteners; for higher-stress corners (doorways, high-traffic walls), you can drill through the base and use #6 screws at the preformed pilot points. Off-white PVC won't yellow under fluorescent or LED lighting, so retrofits blend into existing Panduit raceway systems without a patchwork appearance.
Integrators spec the RAFC10IW-X when running low-voltage cabling along baseboards, chair rails, or ceiling perimeters in commercial spaces—offices, retail back-of-house, healthcare clinics, schools—where fishing wire through walls isn't feasible due to concrete/CMU construction, asbestos abatement costs, or tenant lease restrictions. Surface raceway keeps cables accessible for adds/moves/changes while meeting NEC Article 800 (communications circuits) and TIA-568 cable-support requirements.
The 10-piece pack supports a typical conference-room retrofit (four corners plus spare fittings) or a small-office camera/access-control installation where you're dropping five to eight runs from a central rack. Pair with Panduit LD10 base and cover, inside/outside elbows, and surface-mount boxes to build a complete pathway system. Carton quantity of 50 fits larger rollouts—multitenant office buildings, K-12 classroom wings—where you're standardizing on Pan-Way across 20+ rooms and need volume pricing without custom orders.
The RAFC10IW-X solves the corner-routing problem every integrator faces on surface-mount jobs: you can't just bend LD10 raceway 90 degrees without crushing cables or cracking the PVC, and cutting/mitering fittings on-site wastes billable time. This factory-molded right-angle fitting gives you a TIA/EIA-compliant corner in under a minute—snap the fitting onto the raceway joint, lift the hinged cover, lay in your cables, close the lid. UL94V-0 and FT4 ratings mean you can document fire-safety compliance for AHJ inspections without waiting for engineer letters or field testing. For LD10/LDPH10 retrofit projects where clean aesthetics and fast installation drive scope decisions, the RAFC10IW-X is the fitting that keeps cable pathways both code-compliant and installer-friendly.
