Panduit F2X4WH6 PVC Slotted Wiring Duct 2x4 White 6-Pack

Overview

The Panduit F2X4WH6 is a 2x4 slotted PVC wiring duct sold in a pack of six, designed for organizing and routing control wiring, low-voltage cabling, and signal runs inside electrical enclosures, panels, and relay racks. At 2.25 inches wide by 4.10 inches tall (57.2 x 104.1 mm), this duct size sits in the mid-range of Panduit's NSD series — large enough to handle moderate wire fill in structured cabling panels and security control enclosures, without consuming the footprint that a 4x4 section would. White finish integrates cleanly into standard electrical panel interiors and makes labeling or tracing conductors straightforward.

Installers working in commercial security, access control head-end rooms, or surveillance NVR enclosures will find this a practical channel for keeping home-run cabling separated from power wiring — a wiring practice that matters for both EMI management and long-term serviceability. The F2X4WH6 ships as a minimum-quantity pack of six, which suits panel builds where multiple duct runs of the same size are standard.

Key Features

• UL94 V-0 Flame Rating: V-0 is the highest self-extinguishing classification in UL94 — this duct stops burning within 10 seconds of flame removal and produces no flaming drips. In electrical enclosures and network infrastructure cabinets where a wiring fault could ignite adjacent material, V-0 is the correct spec to specify; lower-rated ducts are a liability in occupied commercial buildings.
• 122°F (50°C) Continuous Use Temperature: UL Recognized for continuous operation at 50°C — relevant in enclosed equipment rooms or outdoor-rated enclosures where ambient temperatures climb. Most PVC duct runs fail or deform well below this threshold, so the UL recognition provides a documented margin for hot environments rather than a guess.
• 2.25 x 4.10 In. Cross Section (57.2 x 104.1 mm): The taller-than-wide profile gives a high wire-fill capacity relative to panel footprint. For IP camera head-end panels or access control wiring consolidation points that carry many small-gauge conductors, the 4.10-inch depth keeps fills manageable and prevents crush damage to jacket insulation on tightly packed runs.
• 0.2-Inch (5mm) Slot Width: Narrow slots prevent smaller conductors from migrating out of the duct unintentionally while still allowing standard wire exit at any point along the run. This is particularly practical for 22–18 AWG signal wire common in access control and intercom wiring — wide-slot ducts let lightweight wire escape and tangle.
• Standard Mounting Holes: Pre-punched standard mounting hole pattern means no drilling or custom jig work — mount directly to din-rail adjacent surfaces or panel back plates using standard hardware. Reduces installation time on repetitive panel builds.
• RoHS Compliant: Meets EU RoHS Directive restrictions on hazardous substances. Required for equipment shipped or installed in the EU, and increasingly specified in domestic commercial and government projects as a baseline procurement standard.
• PVC Construction: PVC offers dimensional stability, resistance to common cleaning chemicals, and adequate rigidity for vertical and horizontal runs without additional support at typical panel-interior span lengths. Appropriate for dry and temperature-controlled indoor environments.
• Pack of 6 (Minimum Order Quantity): Six-piece pack aligns with the practical reality of panel builds — most enclosures need multiple parallel duct runs. Buying in the minimum pack quantity reduces per-unit cost compared to single-piece orders and avoids the common problem of running short mid-install.

Integration & Compatibility

The F2X4WH6 is compatible with Panduit's NSD series duct accessories — covers, reducers, end caps, and tee fittings — allowing full system builds with matched components. The 2x4 cross section is a common size across multiple wiring duct manufacturers, so where Panduit-specific accessories are unavailable, standard 2x4-format fittings from compatible brands may fit, though dimensional tolerances should be verified before specifying non-Panduit accessories on a tight build. This duct is suited for use alongside Panduit's broader cabling and infrastructure line in panel and enclosure builds. Pair with Panduit duct cover stock (sold separately) to fully enclose wire runs where cover is required by the installation standard or the AHJ.

Frequently Asked Questions

Q: What is the actual interior dimension of the F2X4WH6 duct?

A: The duct measures 2.25 inches wide by 4.10 inches tall (57.2 x 104.1 mm). Note that the nominal