Middle Atlantic NM TEE 2800 White - 2815-WH

Middle Atlantic 2815-WH 2800 Series PVC Tee Fitting

Overview

The Middle Atlantic 2815-WH is a white PVC tee fitting designed specifically for the 2800 Series non-metallic uniduct raceway system. If you're routing cable runs through a junction point — splitting a trunk into a branch, or feeding a secondary path off a main duct run — the 2815-WH is the piece that lets you do it cleanly and consistently within the same Middle Atlantic raceway family. The fitting ships in white to match standard 2800 Series duct installed in office environments, server rooms, and AV/security infrastructure builds where aesthetics matter alongside function.

The 2815-WH (often searched as 2815 WH) is sold as a single unit, so quantity planning is on the installer — map your tee junction count before ordering to avoid stalling a pull mid-run.

Key Features

• 2800 Series compatibility: Engineered to mate with Middle Atlantic's 2800 Series non-metallic uniduct. Using a mismatched tee creates gaps at the joint, defeating the dust and physical protection the raceway is there to provide. This fitting eliminates that risk by design.
• PVC construction: Polyvinyl chloride is the standard material for non-metallic cable management in commercial and light-industrial builds — it's lightweight, doesn't corrode, and is easy to cut or modify on site when routing requires it. It also doesn't add grounding complexity the way metallic duct does.
• Maximum 3.2 cm cable diameter: The internal clearance accommodates cables up to 3.2 cm in diameter, which covers most Cat6, low-voltage security cabling, and bundled runs of smaller gauge wire. If you're pulling large conduit or thick multi-conductor trunk cable, verify your bundle diameter before spec'ing this fitting.
• White finish: Matches standard 2800 Series white duct for a consistent appearance on exposed runs — wall-mounted corridor installations, above-desk cable management in open offices, or visible AV/security cable paths where a mismatched color stands out.
• TAA compliant: Meets Trade Agreements Act requirements, making it eligible for federal and government-funded installations where TAA compliance is a procurement condition. The 2815-WH carries this designation, so it can go into those jobs without a compliance exception.
• Single-unit packaging: Sold individually rather than in bulk packs, giving you precise quantity control on projects where you're counting every fitting against a material list.

Integration & Compatibility

The 2815-WH is purpose-built for the 2800 Series non-metallic uniduct product family from Middle Atlantic. It is not a universal fitting — if your installed duct is from a different series or manufacturer, verify dimensional compatibility before ordering. The tee configuration makes it the right choice specifically at branch junction points in a duct run; for straight runs, in-line connectors from the same 2800 Series family are the appropriate selection. This fitting is suitable for low-voltage cabling environments including access control, IP camera cable runs, AV signal cabling, and general structured wiring where non-metallic raceway is specified.

Frequently Asked Questions

Q: Is the 2815-WH TAA compliant?

A: Yes. The 2815-WH is TAA compliant, making it eligible for federal and government-funded projects where Trade Agreements Act compliance is a procurement requirement.

Q: What raceway series is the 2815-WH compatible with?

A: The 2815-WH is designed specifically for Middle Atlantic's 2800 Series non-metallic uniduct. It is not a universal fitting and should be used exclusively within the 2800 Series system to ensure proper fit and continuity of the raceway.

Q: What is the maximum cable diameter the 2815-WH can accommodate?

A: The fitting accommodates a maximum cable diameter of 3.2 cm. Verify your cable bundle diameter before ordering if you are pulling large or bundled runs.

Q: Is the 2815-WH sold individually or in bulk?

A: It is sold as a single unit (1 piece per pack). Plan your tee junction count ahead of ordering to ensure you have the right quantity for the job.

Q: What material is the 2815-WH made from?

A: The fitting is constructed from polyvinyl chloride (PVC), consistent with the non-metallic construction of the 2800 Series uniduct family.

Karl Wilson

The 2815-WH is a single-purpose piece: it handles the tee junction in a Middle Atlantic 2800 Series non-metallic uniduct run, and it does that one job well. The 3.2 cm maximum cable diameter spec is the number installers actually need to verify before they commit a material list — I've seen jobs stall at the fitting stage because someone assumed clearance without checking the bundle diameter against what the tee would actually pass.

Technical Highlights:

• PVC non-metallic construction: No grounding path concerns, no corrosion risk, field-cuttable on site when a run needs minor adjustment. Standard for low-voltage commercial cable management.
• TAA compliance: Government, DoD, and federally-funded integrations often have hard TAA gates in their procurement specs. The 2815-WH clears that gate without requiring a compliance exception or product substitution.
• 3.2 cm max cable diameter: Covers most Cat6 and low-voltage security cable runs comfortably. The constraint matters most when aggregating multiple cables through a single tee — add up your bundle before specifying.

Deployment Considerations:

• This fitting is series-specific — it is engineered for 2800 Series duct only. Mixing it with other Middle Atlantic series or third-party duct will produce an imprecise fit at the joint, compromising raceway integrity.
• Sold as a single unit, not a multi-pack. On larger installations with many branch points, track junction count early in the design phase to avoid short-ordering.

Best fit for government facilities, federal integrations, and commercial security buildouts running 2800 Series uniduct where TAA-compliant hardware is a hard procurement requirement at every bill-of-materials line item.