Middle Atlantic 810A2 Non-Metallic Entrance End Fitting

Overview

The 810A2 is a non-metallic entrance end fitting sized for 800-series surface raceway, finished in ivory to match standard 800-series channel and fittings. It terminates the open end of a raceway run at a wall, panel, or equipment entry point, giving cable a protected transition point instead of an exposed raceway edge. At 0.146 lbs per unit, it adds negligible weight to a run and installs without special tools.

Key Features

• Plastic construction: molded plastic keeps the fitting lightweight and non-conductive, which matters at the raceway's cable entry/exit point where you don't want a metal edge near conductors.
• 600V rating: the 810A2 is rated for use in raceway systems carrying up to 600V, which covers the branch-circuit and low-voltage runs typical of 800-series commercial installs — confirm your specific circuit voltage against this ceiling before specifying.
• cULus Listed / UL Listed: third-party safety listing to UL standards, relevant for inspectors and AHJs who require listed raceway components on commercial jobs.
• RoHS compliant: restricts hazardous substances in the material, a factor if the job specifies RoHS-compliant materials for environmental or procurement reasons.
• Ivory finish: matches standard 800-series raceway and fitting color, so the entrance point doesn't stand out against the rest of the run in finished commercial spaces.
• TAA compliant: relevant for government and federal-funded projects that require Trade Agreements Act compliant sourcing.

Integration & Compatibility

The 810A2 is built to the 800-series raceway form factor and is intended for use with matching 800-series channel, elbows, and couplings rather than as a stand-alone part. If you're specifying a full raceway run, plan the entrance end fitting alongside your other structured cabling accessories and review a cable pathway planning guide before finalizing a bill of materials — end fittings are easy to leave off a first-pass takeoff. Pair it with compatible mounting hardware for the rest of the run, and check the Middle Atlantic catalog for matching ivory-finish 800-series components to keep the run visually consistent.

Frequently Asked Questions

Q: What voltage is the 810A2 rated for?

A: The 810A2 is rated for use in raceway systems up to 600V.

Q: Is the 810A2 UL listed?

A: Yes, the 810A2 is cULus Listed and UL Listed.

Q: What color is the 810A2?

A: Ivory, matching standard 800-series raceway finish.

Q: Is the 810A2 TAA compliant?

A: Yes, the 810A2 is TAA compliant.

Karl Wilson

The 810A2 is a small part, but it's the kind of thing that gets left off a raceway takeoff and holds up a punch-list closeout. It's a non-metallic entrance end fitting for 800-series raceway, ivory finish, and it's the piece that terminates your run cleanly at a wall or panel entry instead of leaving a cut raceway edge exposed.

Technical Highlights:

• 600V rating: covers standard branch-circuit and low-voltage raceway runs — check your circuit's actual voltage against this ceiling before you spec it on anything unusual.
• cULus / UL Listed: gives you a listed component to point to if an inspector questions the raceway accessories on a commercial job.
• 0.146 lbs: light enough that it doesn't factor into raceway load calculations — it's a terminal fitting, not a structural one.

Deployment Considerations:

• Match the ivory finish against your existing 800-series stock before ordering — raceway finish runs vary enough between batches that it's worth a visual check on a visible install.
• This is a plastic molded fitting, not metal — fine for its intended non-conductive entrance-point role, but don't substitute it where a job spec calls for a metallic fitting.

Good fit for finishing out an 800-series raceway run in a commercial office or retail space where the cabling enters a wall or panel and you need a clean, code-listed termination point rather than an exposed cut edge — the 810A2 is the part you order alongside the run, not instead of it.