Middle Atlantic 810A2-WH NM Series 800 Raceway End Fitting

The 810A2-WH is a plastic end fitting for Middle Atlantic's NM Series 800 surface raceway system, finished in white to close out exposed raceway runs cleanly. It's a small part with one job: capping and finishing the termination point of an 800-series raceway run so cable stays enclosed and the installation passes a visual inspection. For integrators running structured cabling, AV wiring, or security cabling behind a raceway system, a fitting like the 810A2-WH is the difference between a finished job and a raw pipe end left exposed on a wall.

Overview

Model 810A2-WH is part of the NM Series 800 fitting family, built in plastic and finished white to match standard 800 raceway housings. It's rated at 0.01 lbs per unit — a lightweight accessory piece, not a structural component — and is intended for indoor installation only. The fitting is UL Listed and cULus Listed, RoHS compliant, and CEC listed, and it carries a 600V voltage rating consistent with the raceway system it terminates. It is also listed as TAA compliant, which matters for integrators bidding government or federally funded projects with Trade Agreements Act sourcing requirements.

Key Features

• Plastic construction: Keeps the fitting lightweight (0.01 lbs/each) and non-conductive, which matters when you're capping a raceway run that carries both power and low-voltage cabling in adjacent channels.
• White finish: Matches standard NM Series 800 raceway housing color, so the end cap doesn't stand out as a mismatched patch on an otherwise clean wall run — important on customer-facing installs like reception areas, retail counters, and conference rooms.
• 600V rating: Confirms the fitting is engineered to the same electrical safety class as the raceway system itself, not a generic cosmetic cap — relevant if the raceway is carrying power circuits alongside data or AV cable.
• UL Listed and cULus Listed: Third-party safety certification for both U.S. and Canadian markets, which most commercial AHJs (authorities having jurisdiction) will want to see on the inspection paperwork before signing off a job.
• RoHS compliant: Confirms the fitting is manufactured without restricted hazardous substances (lead, mercury, certain flame retardants) — relevant for projects with environmental procurement requirements.
• CEC listed: Meets California Energy Commission listing requirements, useful for jobs specified or inspected under California code.
• TAA compliant: Supports Trade Agreements Act sourcing rules, a common requirement on federal and state government bids.
• Indoor rated: Built for interior raceway runs — plan on a different fitting or enclosure class if any part of the run is exposed to weather.

Integration & Compatibility

The 810A2-WH is designed to terminate runs of Middle Atlantic's NM Series 800 raceway — it is a system-specific accessory, not a universal fitting, so it should be paired with matching 800-series raceway and other 800-series fittings for a consistent finish and fit. If you're speccing a full raceway run for a rack room, AV closet, or cable pathway, review the broader Middle Atlantic catalog alongside a PoE and cable planning guide to make sure your raceway sizing accounts for the camera, network, and power runs you're routing behind it. Integrators building out camera or access control cable pathways often pair raceway systems like this with network video recorders and PoE switches mounted in the same equipment room, and with cable management accessories from the same cable management category to keep the finished run consistent end to end.

Frequently Asked Questions

Q: Is the 810A2-WH TAA compliant?

A: Yes, the 810A2-WH is listed as TAA compliant, which supports Trade Agreements Act sourcing requirements on government and federally funded bids.

Q: Is the 810A2-WH rated for outdoor use?

A: No, the 810A2-WH is rated for indoor use only.

Q: What voltage is the 810A2-WH rated for?

A: The 810A2-WH carries a 600V rating, matching the electrical safety class of the NM Series 800 raceway system it's designed to terminate.

Q: What certifications does the 810A2-WH carry?

A: The 810A2-WH is UL Listed, cULus Listed, RoHS compliant, and CEC listed.

Q: What material is the 810A2-WH made from?

A: The 810A2-WH is made from plastic, finished in white to match NM Series 800 raceway housings.

Ted Perry

The 810A2-WH is a small piece of hardware, but on a raceway run it's the part that either looks finished or looks like an afterthought. It's the end fitting for Middle Atlantic's NM Series 800 raceway, molded in white plastic and rated to 600V to match the raceway system it caps off.

Technical Highlights:

• 600V rating: Tells you this isn't a cosmetic-only cap — it's built to the same electrical class as the raceway itself, so it holds up if the run is carrying power circuits.
• UL Listed / cULus Listed: Covers both U.S. and Canadian inspection requirements, which keeps the job moving on commercial installs where the AHJ wants listed components on the pathway.
• 0.01 lbs/each: Negligible weight — this is a finishing accessory, not something that affects raceway load or mounting hardware selection.

Deployment Considerations:

• This is an indoor-only fitting — don't spec it for any raceway run that steps outside, even briefly, at a building penetration.
• It's system-specific to NM Series 800 raceway. Match it to 800-series housing and don't try to force-fit it onto a different raceway series from the same or another manufacturer.

Good fit for a commercial rack room or AV closet buildout where you're running Middle Atlantic 800-series raceway to route camera, network, or AV cable along a wall or equipment rack, and you need a clean, code-listed termination point rather than an exposed raceway end.