Middle Atlantic Narrow 70IN Gray W/11 5- - 7011BCS

Middle Atlantic 7011BCS Rack Outlet Strip — 15A CabinetMATE Power Distribution

Overview

The Middle Atlantic 7011BCS is a 15-amp plug-in outlet center designed for installation inside AV, security, and network equipment racks. Built around the CabinetMATE form factor, it delivers structured in-rack power distribution without requiring hardwired circuits — a practical fit for integrators commissioning control rooms, head-end closets, and security equipment enclosures. TAA compliance means federal and government-funded deployments can proceed without procurement exceptions. For broader context on Middle Atlantic's rack power line, the Middle Atlantic catalog covers the full range of outlet centers and power conditioners.

Key Features

• 15-Amp Capacity: Handles the aggregate draw of typical rack loads — NVRs, PoE switches, servers, and AV gear — without tripping breakers under normal operating conditions. Size your total load against this 15A ceiling before specifying.
• 6 ft (1.8 m) Cord Length: Reaches standard rack-to-PDU distances in most equipment rooms without extension cords. If your rack is positioned far from a wall outlet or floor PDU, verify the run before ordering — 6 ft is fixed.
• TAA Compliant: Meets Trade Agreements Act requirements for government, defense, and GSA schedule purchases. If your project has Buy American or TAA provisions, the 7011BCS satisfies them. Useful for rack power procurement on federally funded security and surveillance projects.

Integration & Compatibility

The 7011BCS is designed for Middle Atlantic rack enclosures but will mount in any standard rack that accepts the CabinetMATE bracket profile. Pair it with a rack enclosure or open-frame rack where internal power distribution is needed. For multi-zone surveillance builds requiring higher amperage or dedicated circuit protection, consider stepping up to a surge-protected or metered PDU from the power distribution category. If you're specifying power for IP cameras or PoE switches, a PoE switch with its own power supply may reduce the outlet load on this strip.

Frequently Asked Questions

Q: Is the Middle Atlantic 7011BCS TAA compliant?

A: Yes. The 7011BCS is confirmed TAA compliant, making it eligible for government, GSA, and federally funded project procurement.

Q: What is the amperage rating of the 7011BCS?

A: The 7011BCS is rated at 15 amps. Total connected load across all outlets must stay within this limit.

Q: How long is the power cord on the 7011BCS?

A: The cord is 6 ft (1.8 m). This is a fixed length — no extension is built in.

Q: Will the 7011BCS fit in non-Middle Atlantic racks?

A: The CabinetMATE design targets Middle Atlantic enclosures, but compatibility with third-party racks depends on the bracket profile of that rack. Verify mounting dimensions before ordering if installing in a non-Middle Atlantic enclosure.

Jerry Tildsen

The 7011BCS is a 15-amp CabinetMATE outlet strip — straightforward in-rack power distribution with a 6 ft cord and TAA compliance confirmed. I specify this when a project needs internal outlet capacity inside a Middle Atlantic enclosure without running a dedicated hardwired circuit to the rack.

Technical Highlights:

• 15A Rating: Sufficient for most mixed security rack loads — NVR, switch, and ancillary gear — but requires load accounting before spec. Don't assume 15A is unlimited headroom on a dense rack.
• 6 ft Fixed Cord: Works for standard rack placements within a few feet of a wall outlet. Longer runs to a floor PDU or panel may need a different approach entirely.
• TAA Compliant: Eliminates a procurement hurdle on government security contracts and GSA schedule projects. Worth calling out explicitly in submittals.

Deployment Considerations:

• Verify that total rack load stays under 15A before finalizing the bill of materials — NVRs with spinning drives and PoE switches under load can add up faster than estimated.
• Mounting compatibility outside Middle Atlantic enclosures is not guaranteed by the evidence — confirm bracket fit if the enclosure is a third-party brand.

The 7011BCS is the right call for government-funded security head-end builds inside Middle Atlantic racks where TAA compliance is a hard requirement and in-rack outlet access is needed without dedicated circuit work.