APC by Schneider Electric Hyperpod Door - Dual Sliding Doors - FS-DR-1001-B

APC by Schneider Electric FS-DR-1001-B HyperPod Dual Sliding Door

Overview

The APC by Schneider Electric FS-DR-1001-B is a dual sliding door assembly purpose-built for the APC HyperPod modular data center enclosure system. At 550 mm wide and 2,135 mm tall — with a 225 mm depth profile — this door panel is dimensioned to integrate flush with HyperPod module bays, maintaining the structural and aesthetic continuity of your modular deployment. If you are expanding or replacing door panels on an existing HyperPod installation, the FS-DR-1001-B (often searched as FS DR 1001 B) is the factory-specified dual sliding configuration for that platform.

Sliding door mechanisms are the correct choice for HyperPod rows where swing clearance is limited — dense aisle containment setups, back-to-back cabinet arrangements, or hot-aisle/cold-aisle corridors where a hinged door would obstruct access or airflow management panels. The sliding action keeps the access footprint minimal while still providing full panel clearance across the 550 mm bay opening.

Key Features

• Dual Sliding Configuration: Two-panel sliding design allows full bay access without requiring swing clearance in front of or behind the door — critical in tight HyperPod row configurations where aisle width is constrained by containment hardware or floor PDUs.
• 550 mm Width, 2,135 mm Height: Dimensioned to the HyperPod module bay specification. Correct fitment means no field modification, no shimming, and no gap in the enclosure's physical security or containment integrity. Verify your HyperPod bay width matches 550 mm before ordering.
• 225 mm Depth Profile: The shallow 225 mm depth keeps the door assembly within the HyperPod envelope, avoiding protrusion into aisle pathways. Relevant where aisle containment curtains or overhead busbars are close to the enclosure face.
• Purpose-Built HyperPod Compatibility: Designed specifically for APC HyperPod — not a generic panel. This matters for containment seal integrity, locking mechanism alignment, and structural load rating. Using non-specified door assemblies on HyperPod modules risks voiding support agreements and compromising the enclosure's thermal management design.
• Factory-New Component: Sourced as a genuine factory-new replacement or expansion part — not a field-fabricated substitute. Consistent finish and hardware tolerances ensure proper operation of the sliding mechanism and latch points out of the box.
• Manageable Shipping Footprint: Packaged at 630 mm × 2,205 mm × 385 mm with a gross weight of 80 kg. Plan for freight delivery and at least a two-person installation team — this is not a parcel-shipped component. Verify loading dock or freight elevator access before scheduling delivery.

Integration & Compatibility

The FS-DR-1001-B is compatible with the APC by Schneider Electric HyperPod modular enclosure platform. If you are configuring a new HyperPod deployment or replacing a damaged door on an existing installation, confirm the specific HyperPod module bay width against the 550 mm specification of this door. HyperPod installations vary by row configuration and module count — cross-reference your HyperPod data center infrastructure bill of materials or site documentation before ordering replacement panels.

For complete modular data center builds, the door assembly should be coordinated with HyperPod frame components, containment panels, and power distribution accessories to ensure the enclosure row closes out correctly. If your project involves multiple bays, order door quantities matched to your bay count — this FS-DR-1001-B unit covers a single 550 mm bay position with dual sliding panels.

What's in the Box

Packaged dimensions: 630 mm wide × 2,205 mm deep × 385 mm high. Gross packaged weight: 80 kg. Verify freight receiving capacity prior to delivery. Specific included hardware and fastener counts are not confirmed in available documentation — contact your freight carrier for liftgate requirements.

Frequently Asked Questions

Q: What enclosure system is the FS-DR-1001-B designed for?

A: The FS-DR-1001-B is designed specifically for the APC HyperPod modular data center enclosure platform. It is not a universal or generic door panel and is not confirmed compatible with other APC enclosure lines.

Q: What are the door panel dimensions?

A: The FS-DR-1001-B measures 550 mm wide × 2,135 mm tall × 225 mm deep. These dimensions correspond to the HyperPod bay opening specification — verify your bay width before ordering.

Q: Why choose a sliding door over a hinged door for a HyperPod installation?

A: Sliding doors eliminate swing clearance requirements in front of the enclosure. In dense HyperPod row deployments with hot-aisle/cold-aisle containment, airflow panels, or limited aisle width, a sliding mechanism allows full bay access without obstructing adjacent equipment or walkways.

Q: How heavy is the FS-DR-1001-B shipment?

A: The packaged unit weighs 80 kg (approximately 176 lbs) and ships in a 630 mm × 2,205 mm × 385 mm carton. Freight delivery with liftgate service and a two-person receiving team is recommended.

Q: Is the FS-DR-1001-B sold as a single unit covering one bay?

A: Yes. One FS-DR-1001-B covers a single 550 mm HyperPod bay position with a dual sliding door configuration. Order quantities should match your bay count for full row coverage.

Marty Allison

The FS-DR-1001-B is a straightforward but dimension-critical component — the 550 mm bay width is a hard constraint, and it is the first thing I verify on any HyperPod expansion project before a door order goes in. One wrong measurement and you are coordinating a freight return on an 80 kg carton.

Technical Highlights:

• 550 mm × 2,135 mm Bay Fit: Matches the HyperPod module bay specification exactly — no field cutting or shimming required. Consistent tolerances from a factory-new component mean the sliding mechanism and latch hardware align correctly on first install.
• 225 mm Depth Envelope: Keeps the door within the HyperPod structural profile. In containment-equipped rows, this prevents the door from fouling overhead busway, containment ribs, or blanking panels on adjacent modules.
• 80 kg Packaged Weight: At 80 kg gross in a 2,205 mm carton, this requires freight delivery planning — not just a standard UPS drop. Confirm liftgate, dock height, and at minimum a two-person crew before the truck arrives.

Deployment Considerations:

• Verify HyperPod bay width is exactly 550 mm against your site documentation before ordering — HyperPod configurations vary and a bay mismatch means a full return/exchange on a freight-class item.
• This door assembly is HyperPod-specific. Do not attempt to fit it to standard APC NetShelter or Symmetra enclosure frames — mounting points, latch geometry, and sliding track dimensions are not cross-compatible.

The FS-DR-1001-B is the right order for a HyperPod row buildout or field replacement where aisle clearance is tight and sliding access is the specified configuration — particularly in high-density colocation rows or modular edge deployments where every centimeter of aisle width has been allocated.