Comelit PAC-CD-FB-PACC-CLP Proximity Key Fob 10-Pack
Overview
The Comelit PAC-CD-FB-PACC-CLP is a proximity key fob credential designed for multi-door access control deployments. Supplied as a 10-pack, this quantity addresses common rollout and expansion scenarios where standardized credentials need rapid distribution across residential and commercial facilities. Each fob pairs with Comelit PAC-series proximity readers and access control infrastructure, functioning as a secure access token that integrates into existing control networks without requiring additional gateway or protocol conversion.
Proximity-based authentication eliminates the latency and user friction of keypad entry — residents, tenants, and staff simply present the fob to a reader; no PIN recall required, no fumbling. For integrators managing multi-unit residential buildings, office parks, or warehouse access, the ability to provision 10 credentials simultaneously reduces commissioning time and simplifies credential inventory management.
Key Features
- 10-Unit Pack Quantity: Reduces per-unit logistics cost and ensures consistent credential supply for phased rollouts or multi-door installations. You provision credentials in bulk, cutting overhead on individual fob shipments.
- PAC-Series Compatibility: Works natively with Comelit PAC proximity readers and control modules. No bridging hardware or third-party middleware needed — one vendor, one protocol stack, simplified troubleshooting.
- Proximity Technology: Radio-frequency identification (RFID) credential at 13.56 MHz or lower (standard for access control fobs). No battery drain on the fob itself — passive operation means each unit has an indefinite lifespan unless physically damaged.
- Compact Form Factor: Keychain-sized credential fits standard wallet, pocket, or lanyard attachment. Portable and user-friendly, reducing drop-off or loss during handover to tenants or employees.
- Credential Enrollment: Each fob carries a unique identifier (serial or UID) registered in the Comelit access control database. Revocation, reassignment, and audit trail capture integrate with the host PAC platform's user management interface.
- Residential and Commercial Fit: Equally deployable in apartment complexes, office buildings, warehouse receiving areas, or mixed-use facilities. No environmental constraints specific to indoor vs. outdoor mounting — the credential itself operates indoors; outdoor readers require separate weatherproofing via reader enclosures.
Integration & Compatibility
The PAC-CD-FB-PACC-CLP integrates with Comelit PAC proximity reader hardware and access control panels. Provisioning occurs through the Comelit management interface, where each fob's unique identifier is assigned to a user profile, door(s), time-zone rules, and audit events. Multi-reader sites (e.g., main entrance + loading dock + secure area) pair each fob with multiple reader locations; the Comelit control architecture handles rule enforcement at the panel level.
Credential lifespan is indefinite unless enrolled as a temporary (timed) credential or manually revoked. No re-enrollment required unless the fob is lost and must be deactivated retroactively.
What's in the Box
- 10x Proximity key fobs (PAC-CD-FB-PACC-CLP)
When to Choose a Different Approach
Proximity fobs suit deployments prioritizing ease-of-use and standardized credential distribution. If your facility requires multi-factor authentication (fob + PIN), consider pairing proximity fobs with keypad readers that enforce dual-credential validation at the panel level. If you need wireless range exceeding standard proximity (typically 4–8 inches at a reader), consider Comelit's longer-range RFID or mobile-credential options, though these introduce mobile device dependencies and battery management overhead. If credential revocation must occur in real-time across distributed readers without central connectivity, proximity systems require either persistent network backbone or periodic sync — confirm Comelit's PAC offline-mode behavior with your integrator.
Frequently Asked Questions
Q: Can I reprogram the PAC-CD-FB-PACC-CLP fobs after purchase?
A: No, the fobs ship with fixed manufacturer-assigned IDs. Reprogramming the access privileges occurs in the Comelit control panel or management software — you enroll each fob's unique identifier into user profiles and assign permissions. If a fob's ID becomes corrupted or unreadable, replacement fobs are ordered separately; the PAC-CD-FB-PACC-CLP 10-pack includes new, virgin units.
Q: Will the PAC-CD-FB-PACC-CLP work with third-party proximity readers?
A: These fobs are designed and certified for Comelit PAC-series readers and infrastructure. Use with non-Comelit readers is not supported and may fail due to protocol or frequency incompatibility. For multi-vendor environments, consult with your integrator about credential gateway solutions or stick to Comelit readers throughout.
Q: What's the operating range from the fob to the reader?
A: Proximity fobs typically operate at 4–8 inches from the reader face, depending on reader sensitivity and environmental RF interference. Specific range specs for the PAC-CD-FB-PACC-CLP are detailed in the PAC series proximity reader documentation; refer to the reader product page for exact performance figures.
Q: Can I mix PAC-CD-FB-PACC-CLP fobs with other Comelit credential types (cards, tags)?
A: Yes, provided the readers and control panel support multiple credential types. Comelit PAC systems often accommodate both fobs and cards on the same reader. Verify with your panel firmware version and reader model whether dual-credential support is enabled.
Q: Is there a warranty on these fobs?
A: Warranty terms are determined by Comelit's standard terms and your distributor's policy. Physical damage (cracked plastic, delaminated badge) or loss due to user negligence are typically not covered. Confirm with your equipment supplier before purchase.
Q: How do I deactivate a lost or stolen fob?
A: Log into the Comelit management interface, locate the compromised fob's ID in your user database, and revoke or delete the credential. The change propagates to all readers on the network during the next sync cycle (typically real-time if readers maintain network connectivity). If your system operates in offline mode, credential revocation may require local re-sync or firmware update — coordinate with your integrator.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The Comelit PAC-CD-FB-PACC-CLP is a straightforward proximity fob 10-pack with one job: deploy standardized RFID credentials across a Comelit PAC-series access control footprint without inventory friction. The 10-unit quantity is the right call for phased residential or commercial rollouts where you want to batch-provision credentials and avoid per-fob shipping overhead.
Technical Highlights:
- Passive RFID Operation: No battery in the fob means zero maintenance overhead and infinite shelf life pre-enrollment. Each credential carries a unique factory-assigned ID that enrolls once in the Comelit database — no re-sync required unless the fob is physically lost or flagged for revocation.
- 10-Pack Bulk Efficiency: Reduces per-unit logistics cost and ensures consistent credentials across a multi-unit property. You can provision all 10 fobs into a single user profile or distribute them across 10 separate residents/staff in a single software session.
- PAC-Series Native Integration: Works directly with Comelit PAC proximity readers and control panels. No bridge hardware, no protocol translation — one vendor, one stack, minimal troubleshooting surface.
Deployment Considerations:
- Proximity range is short (typically 4–8 inches at the reader face) — confirm reader placement allows comfortable fob presentation without fumbling, especially for elderly or mobility-limited tenants.
- Credential enrollment is one-way. Once a fob's ID is registered in the Comelit system, you cannot reprogram it. Lost fobs must be revoked in the control panel and replaced — keep spare fobs on hand for high-turnover properties.
- Multi-reader sites require the Comelit control panel to enforce door and time-zone rules. If readers operate offline, confirm sync strategy with your integrator before deployment.
The PAC-CD-FB-PACC-CLP is a fit for residential apartment buildings, small office complexes, and warehouse receiving areas where credential standardization and ease-of-use outweigh advanced multi-factor or mobile-credential requirements. For high-security zones or facilities requiring dual authentication, layer fobs with keypad validation at the panel level.
