Panduit UTP6AX6MOR 10Gig 6m Orange Cat 6A Patch Cord

Panduit UTP6AX6MOR TX6A 10Gig Cat 6A UTP Patch Cord

The Panduit UTP6AX6MOR delivers 10GBASE-T performance in a 6-meter patch cord engineered for datacenter and enterprise network deployments where alien crosstalk, documentation accuracy, and cable management determine uptime. Built on 24 AWG solid copper conductors with U/UTP construction, this Cat 6A patch cord exceeds ANSI/TIA-568.2-D and ISO 11801 Class EA requirements for 10 Gb/s transmission up to 100 meters. The orange jacket provides instant visual identification in structured cabling systems, while RapidID pre-installed barcodes eliminate manual labeling errors during commissioning and audits. Tangle-free latches prevent snags in high-density patch panels, and 802.3bt Type 3/4 PoE++ certification supports up to 90W power delivery for WAPs, PTZ cameras, and building automation controllers on the same cable plant.

Key Features

• 10 Gb/s transmission certified to ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA standards
• 24 AWG solid copper conductors in U/UTP construction with 0.250" (6.4mm) diameter
• RapidID pre-installed barcode labels integrate with Panduit RapidID software for automated port mapping and cable documentation
• Tangle-free modular plug latches eliminate snag-induced disconnects during moves, adds, and changes
• IEEE 802.3bt Type 3 and Type 4 PoE++ rated — supports 60W and 90W power budgets over 6-meter runs
• 6-meter (19.7-foot) length bridges equipment racks, cross-connects, and zone distribution points in structured cabling topologies
• Orange jacket enables color-coded circuit identification per TIA-606-C administration standards
• CM flammability rating meets NEC Article 800 requirements for general-purpose horizontal pathways
• Rated for 2,500 mating cycles — withstands frequent reconfigurations in active network environments
• RoHS compliant construction eliminates hazardous substances in datacenter and campus installations

Solid 24 AWG copper conductors distinguish this patch cord from stranded-wire variants commonly used for equipment cords. The solid construction reduces DC resistance and insertion loss across the 1–500 MHz spectrum, critical for maintaining 10GBASE-T signal integrity in permanent and semi-permanent links. U/UTP (unshielded twisted pair) architecture relies on balanced pair geometry and twist rates to cancel electromagnetic interference, eliminating the ground-loop and installation complexity issues associated with shielded alternatives. The 0.250-inch diameter fits standard patch panel port density while remaining flexible enough for tight-radius bends around cable managers. Panduit's TX6A modular plugs terminate each end with 50-microinch gold-plated contacts that maintain <20 milliohm contact resistance through 2,500 insertion cycles, exceeding the IEC 60603-7 durability baseline by 150%. Internal load bars align conductors to TIA T568A/B pinouts, and the plug's staggered-tooth design ensures full contact engagement before the latch clicks — preventing partial-insertion faults that degrade return loss and near-end crosstalk performance.

RapidID integration addresses the documentation gap that plagues large-scale network deployments. Each cord ships with a pre-printed barcode label encoding a unique identifier compatible with Panduit's RapidID port-mapping software. During installation, technicians scan the barcode at the patch panel and again at the equipment port; the software auto-populates link records, eliminates transcription errors, and generates as-built drawings without manual data entry. This workflow cuts commissioning time on 500-port datacenters from days to hours and ensures audit-ready documentation for SOC 2, HIPAA, and PCI DSS compliance regimes. The 6-meter length fits typical equipment-rack-to-MDA (main distribution area) and horizontal-cross-connect-to-telecommunications-room runs in structured cabling topologies, providing enough slack for cable management without excess coil that increases alien crosstalk coupling. Orange jacket color follows TIA-606-C best practices for auxiliary circuits, demarcation points, or secondary network segments — enabling at-a-glance circuit tracing in mixed-vendor patch fields.

Exceeds ANSI/TIA-568.2-D Category 6A channel limits for insertion loss, return loss, near-end crosstalk (NEXT), and alien crosstalk (ANEXT) across the full 1–500 MHz bandwidth. Meets ANSI/TIA-1096-A (formerly FCC Part 68) registration requirements for connection to public telecommunications networks. IEEE 802.3bt Type 3/4 PoE++ certification confirms the cable maintains <12.5Ω DC loop resistance over 6 meters, enabling 60W (Type 3) and 90W (Type 4) PD power budgets without voltage drop violations. UL 1863 listing and CM flammability rating authorize installation in plenum-equivalent air-handling spaces and general-purpose horizontal pathways per NEC Article 800. The combination of 10Gig performance, automated documentation, and PoE++ power delivery makes the UTP6AX6MOR the engineering choice for datacenter top-of-rack switches, enterprise wireless controller uplinks, and IP camera/access control aggregation points where bandwidth, power, and audit trails converge on a single cable plant.