Hanwha SBP-390WM2 Long Wall Mount Arm, Ivory
The Hanwha SBP-390WM2 is a precision aluminum wall mount arm engineered for installations requiring extended reach and deliberate camera positioning. At 417mm (16.4 inches) in length, this mount delivers the standoff distance needed to position cameras at optimal angles without crowding wall infrastructure. Built from aluminum with a powder-coated ivory finish, the SBP-390WM2 (often searched as SBP 390WM2) integrates into both new deployments and retrofit scenarios where aesthetics and structural integrity matter equally.
Key Features
- Extended 417mm reach: Gives you room to angle cameras away from wall surfaces and obstruction, critical in narrow corridors, entry vestibules, or tight retail aisles where a short bracket won't work.
- Aluminum construction: Resists corrosion and vibration better than painted steel — relevant for HVAC zones, loading docks, and manufacturing floors where condensation or thermal cycling is routine.
- Integrated conduit access: Routes cables through the arm itself instead of exposing them on the exterior. Reduces cable sag, protects wiring from physical damage, and keeps the installation looking finished.
- Lightweight at 1.79 kg (3.95 lb): Single-person installation is feasible; minimizes load on wall anchors, which is important if mounting to drywall or composite surfaces that can't handle heavy point loads.
- Compact cross-section (115.0 x 183.0 mm base): Doesn't protrude excessively when viewed from certain angles, keeping the visual footprint professional in office and retail settings.
- Pole and corner mount compatible: Adapts to wall corners or vertical pole runs without requiring additional brackets, simplifying kit assembly and reducing parts inventory.
Integration & Compatibility
The SBP-390WM2 integrates with Hanwha IP camera bodies that support standard ball-mount or quick-release interfaces. Verify your specific camera model's mounting footprint before ordering — attachment compatibility is not universal across the Hanwha IP camera line. Works alongside standard wall-mount hardware and corner adapters. Conduit access is internally routed, meaning you won't need external cable trays or external conduit clips — cable management is contained within the arm profile itself.
Deployment Scenarios
Use the SBP-390WM2 in retail loss-prevention setups where you need to position a camera above POS terminals or merchandise displays with clean sightlines. Warehouse environments benefit from the extended reach when mounting above inventory racks. Corporate lobbies and access-control points require the same standoff distance and finished appearance — the ivory finish blends into lighter architectural finishes without looking like a rough industrial bracket. Manufacturing floors with overhead piping or HVAC runs can use the arm to position cameras away from physical hazards.
When to Consider an Alternative
If you need pan-tilt-zoom (PTZ) camera support, the SBP-390WM2 is a fixed-position arm — it will not rotate or articulate. For very heavy turret or box cameras exceeding 2–3 kg, confirm weight capacity with your supplier or mounting interface. If conduit routing is not required and you prefer simpler installation, a shorter fixed bracket or pendant mount may reduce cost. For outdoor use in salt spray, marine, or extreme UV environments, consult the finish specification — powder-coat alone may not provide adequate protection without additional corrosion inhibitors.
Ted PerryPerspective based on aggregated and affiliated engineering team experience.
The SBP-390WM2 is a genuine workhorse when you need standoff distance without complexity. The 417mm reach is the real differentiator here — most fixed brackets max out at 200–250mm, which is fine for corridor coverage but won't help you position a camera above a counter or away from a wall corner. That integrated conduit passage also eliminates a common post-installation problem: sloppy cable drape and security risks from exposed wiring.
Technical Highlights:
- 417mm arm length: Sufficient reach for most indoor wall-corner and overhang scenarios; reduces the need for ceiling mounts or articulating brackets in retrofit work.
- 1.79 kg weight: Low enough that standard drywall anchors (with proper spacing and fastener choice) can handle it; heavier arms require lag bolts or masonry installation, which adds cost and complexity.
- Aluminum + powder coat: Won't oxidize like bare steel in indoor humidity or light salt-air environments; maintains aesthetics over 5–10 years without touch-up paint.
Deployment Considerations:
- Verify the ball mount or quick-release interface on your camera — not all Hanwha bodies use the same connection pattern. Cross-reference the camera datasheet before committing to this arm.
- Wall anchor selection is critical: drywall anchors are acceptable for 1.79 kg + camera weight in standard studs, but lag bolts into wood or concrete are safer if the wall is plaster, tile, or soft composite materials.
The SBP-390WM2 is the right choice for integrators who've encountered retrofit projects where standard pendant mounts are too short and full PTZ infrastructure is overkill. Retail, warehouse, and office deployments where clean cable routing and moderate standoff are non-negotiable will see the value. For fixed-camera applications with high aesthetic standards, this arm is a solid fit.
Frequently Asked Questions
Q: Is the SBP-390WM2 rated for outdoor use?
A: The ivory powder-coated aluminum construction provides some weather resistance, but manufacturer documentation does not specify an IP rating or explicit outdoor temperature/humidity rating. For direct outdoor exposure (rain, UV, salt spray), confirm with the manufacturer or consider a stainless steel or epoxy-coated bracket designed for outdoor environments.
Q: Can I use the SBP-390WM2 with non-Hanwha cameras?
A: The SBP-390WM2 is designed for Hanwha camera bodies with compatible ball-mount or quick-release interfaces. Using it with third-party cameras requires verifying that the attachment footprint and load limits match. Do not assume universal compatibility.
Q: What wall anchors should I use for installation?
A: At 1.79 kg plus camera weight (typically 400–800g), standard toggle or expansion anchors are adequate for drywall into wood studs. For plaster, hollow block, or soft materials, use lag bolts or concrete anchors. Always use fasteners rated for your wall type and total load.
Q: Does the integrated conduit access fit standard 3/4-inch conduit?
A: The SBP-390WM2 datasheet does not specify conduit diameter. Check the PDF documentation or contact Hanwha technical support to confirm compatibility with your conduit size before installation.
Q: Is the mount height-adjustable after installation?
A: No, the SBP-390WM2 is a fixed-position wall arm. Angle adjustment happens at the camera's ball mount or quick-release connector, not at the arm itself. Plan your wall location carefully for the desired camera pitch.
