Zebra ZBK-ET4X-10VESA-01 ET4X 10" Expansion Back with VESA Mount
Overview
The Zebra ZBK-ET4X-10VESA-01 is a purpose-built mounting accessory for the ET4X 10-inch tablet line. This expansion back enables you to integrate an ET4X tablet into standard VESA-mount infrastructure — display arms, wall frames, kiosk enclosures, and stationary workstation rigs common in warehouse operations, receiving docks, and logistics facilities. If you're deploying mobile tablets but need fixed reference points or hands-free operation at specific stations, this accessory bridges that gap without tethering the device.
Key Features
- VESA 75/100 Compatibility: Mounts directly to any VESA-standard bracket or arm — no proprietary adapters needed. This means you can reuse existing display infrastructure, reducing hardware redundancy and simplifying inventory management across your operation.
- ET4X 10-Inch Specific Design: Engineered for precise fit and weight balance on the ET4X 10-inch form factor. Prevents wobble or drift on articulated arms, which is critical in high-vibration environments like conveyor-fed receiving lines or vehicle-mounted workstations.
- Secure Quick-Release Mechanism: Allows rapid tablet swaps without tools — essential when rotating devices through maintenance cycles or shifting a single tablet between multiple fixed stations throughout a shift.
- Low-Profile Footprint: Doesn't substantially alter the tablet's depth or weight distribution, so existing VESA arms and mounts won't require re-balancing or counterweight adjustment.
- Passive Design (No Power or Connectivity Pass-Through): The ZBK-ET4X-10VESA-01 is a pure mechanical mount. It does not add charging capabilities or pass data lines. If your deployment requires wired charging or Ethernet at the mount point, those must be routed separately — budget for a docking station or USB-C charging arm if 24/7 powered operation is mandatory.
- Durability in Logistics Environments: Materials engineered to withstand daily mounting/dismounting cycles and minor impacts typical in warehouse settings. Not rated for submersion or sustained outdoor rain exposure — this is an indoor to covered-outdoor accessory only.
Integration & Compatibility
The ZBK-ET4X-10VESA-01 works exclusively with Zebra ET4X 10-inch tablets. Verify your tablet SKU against the ET4X 10-inch specification before ordering. If you're deploying multiple tablet sizes (e.g., 8-inch and 10-inch ET4X models), you'll need size-matched expansion backs for each. This accessory integrates seamlessly into any warehouse automation workflow already using ET4X devices — receiving, shipping, cycle count, putaway, and order assembly stations are all common deployment points. Pair this mount with your existing mobile computer management infrastructure (Zebra's EMDK, Analytics, or third-party MDM solutions).
When to Choose a Different Configuration
If your workstation already has a powered docking cradle or you need integrated charging and data synchronization at the mount point, consider a full ET4X docking station instead of the expansion back alone. If you require mounting flexibility beyond VESA (e.g., non-standard arm geometries or magnetic attachment), consult your integrator about custom bracketry or a hybrid mount solution.
Frequently Asked Questions
Q: Does the ZBK-ET4X-10VESA-01 work with 8-inch ET4X tablets?
A: No. This expansion back is engineered for the 10-inch ET4X form factor only. Using it on an 8-inch device will result in poor fit and instability. If you operate both sizes, you'll need separate mounts for each.
Q: Can I attach a charging dock to a VESA arm with this expansion back?
A: The ZBK-ET4X-10VESA-01 is a passive mount only — it does not pass power or data. If you need continuous charging at a fixed station, add a separate USB-C power supply or docking cradle alongside the VESA mount, or choose a powered docking solution instead.
Q: Is this accessory rated for outdoor use?
A: The ZBK-ET4X-10VESA-01 is suitable for covered outdoor areas but not open-air exposure. If your deployment requires rain protection, mount it under an overhang or within an outdoor-rated enclosure. The ET4X tablet itself is rated IP54, but the expansion back is not independently environmental-sealed.
Q: What tools do I need to install the ZBK-ET4X-10VESA-01 on a VESA arm?
A: Standard metric or imperial mounting hardware (typically M4 or M6 bolts) compatible with your VESA arm. Most arms ship with a hardware kit. No special tools are needed beyond a basic wrench or hex key — installation typically takes 5–10 minutes.
Q: Can I remove the expansion back and use the tablet in mobile mode again?
A: Yes. The quick-release design allows you to detach the ZBK-ET4X-10VESA-01 without tools and use the bare ET4X tablet in your mobile workflows. No permanent modifications to the device.
Q: Does VESA mounting support the full weight of the ET4X 10-inch tablet plus the expansion back?
A: Standard VESA arms are rated for displays up to 7–15 kg depending on the model. The ET4X 10-inch is approximately 0.7 kg, and the ZBK-ET4X-10VESA-01 adds minimal mass. Verify your specific arm's weight rating, but most commercial display arms will handle this payload easily.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The ZBK-ET4X-10VESA-01 is a straightforward passive VESA mount designed to anchor the ET4X 10-inch tablet at fixed warehouse stations. It solves a real deployment problem: how to run a tablet as a stationary reference device without a proprietary docking cradle. No power, no data — just mechanical stability and standard VESA compatibility.
Technical Highlights:
- VESA 75/100 Standard: Eliminates vendor lock-in. You can migrate the tablet to any VESA arm, wall mount, or kiosk frame already installed in your facility. This flexibility matters when you're standardizing infrastructure across multiple warehouses.
- Quick-Release Design: Mounting and removal require no tools and take under one minute. Critical for operations that rotate tablets through maintenance, firmware updates, or shift changes without disrupting floor station continuity.
- Passive (No Power/Data Pass-Through): The ZBK-ET4X-10VESA-01 does not include charging contacts or data connectors. Power and connectivity must be routed separately — either via a USB-C charging arm, a nearby power outlet, or docking solution positioned beside the mount. This is a limitation if your spec calls for seamless integrated power, but it's also an advantage: the mount itself is failure-proof and doesn't complicate device firmware or authentication workflows.
Deployment Considerations:
- Verify VESA arm weight rating before deployment. Most commercial arms support this payload easily, but light-duty articulating arms (under 5 kg rated capacity) may drift under repeated adjustment or vibration. Test articulation smoothness under load before full rollout.
- Charging must be provisioned separately — this is not a docking station. If your workflow requires continuous power at the station, budget for a separate USB-C charger or docking cradle alongside the VESA mount. Wireless charging is not an option on the ET4X line.
- The expansion back itself is not environmental-sealed. If your station is exposed to direct sunlight, rain, or high-pressure wash-down (common in some food and beverage warehouses), mount it under cover or in an outdoor-rated protective enclosure.
Position the ZBK-ET4X-10VESA-01 at fixed receiving docks, cycle count stations, or order assembly points where you want the tablet mounted at ergonomic height and the operator needs both hands free. Pair it with a VESA-compatible arm that offers pan-tilt-height adjustment so different operators can find their preferred angle without disassembling the mount.
