Vertiv GL24WDXM-B-SH-00 11U Wall-Mount Network Enclosure

Overview

The Vertiv GL24WDXM-B-SH-00 is an 11U wall-mount enclosure from the WDX series, finished in black and sized at 24 inches wide by 32 inches deep. At 11U of usable rack space, it fits edge deployments — telecom closets, IDF rooms, small equipment rooms, and surveillance head-end installations — where a full floor-standing cabinet is impractical but organized, secure equipment mounting is non-negotiable. The model number GL24WDXM-B-SH-00 (sometimes searched as GL24WDXMBSH00) identifies the 24×32 black wall-mount variant in the WDX product family.

Wall-mount enclosures in the WDX line are designed to keep active network and security equipment off the floor and secured to a structural wall surface, which reduces cable runs to local switches and access control or surveillance gear and simplifies access for technicians working in tight mechanical rooms. The 32-inch depth accommodates standard 1U and 2U rack equipment including patch panels, PoE switches, and NVR appliances without forcing awkward cable management workarounds.

For Vertiv enclosures and power infrastructure, the WDX wall-mount series targets environments where swing-out or fixed-depth mounting is needed in space-constrained locations. The 11U height is a practical middle ground — enough rack space for a small surveillance head-end (NVR, PoE switch, patch panel, UPS) without the footprint of a 12U or larger unit. If your equipment list exceeds 11U, consider a larger variant in the WDX family rather than stacking external accessories.

When evaluating this enclosure for a surveillance head-end rack build or network closet, confirm your heaviest component's weight against the wall-mount load rating in the Vertiv product datasheet — this spec is not available in current evidence and must be verified before installation. Similarly, confirm knockouts and cable entry points match your conduit routing plan before mounting.

Key Considerations

• 11U capacity: fits a compact surveillance stack (NVR, PoE switch, patch panel) in a single enclosure without occupying floor space — a direct benefit in mechanical rooms or stairwell IDF closets with no room for a standing cabinet.
• 24W × 32D footprint: the 32-inch depth handles full-depth 1U/2U rack equipment; shallower 24-inch-depth enclosures would require short-depth or half-depth gear, limiting your component selection.
• Black finish: matches standard rack aesthetics in finished office or retail environments where a grey enclosure would be visually inconsistent.
• Wall-mount form factor: keeps equipment elevated and secured, reducing exposure to floor-level water intrusion and unauthorized physical access in shared utility spaces.

Frequently Asked Questions

Q: What does the GL24WDXM-B-SH-00 part number encode?

A: The WDX designation identifies the Vertiv wall-mount enclosure series. The 24 refers to the 24-inch width, 32 to the 32-inch depth, M to the wall-mount configuration, and B to the black finish. SH-00 identifies the specific door/hardware variant within this configuration.

Q: Is the GL24WDXM-B-SH-00 the same as GL24WDXMBSH00?

A: Yes — GL24WDXMBSH00 is the hyphen-stripped search variation of GL24WDXM-B-SH-00. Both refer to the same Vertiv WDX 11U 24×32 black wall-mount enclosure.

Q: What is the maximum equipment weight this enclosure supports?

A: The load rating for the GL24WDXM-B-SH-00 is not confirmed in current available evidence. Consult the Vertiv WDX series datasheet or contact Vertiv directly to verify the rated load before specifying for heavy equipment installations.

Q: Can this enclosure be used for a surveillance NVR and PoE switch installation?

A: The 11U depth and 32-inch interior depth are well-suited for a compact surveillance head-end. Verify that your NVR and switch models fit within 11U total and that the wall structure can support the combined equipment weight before installation.

Jerry Tildsen

The GL24WDXM-B-SH-00 is a purpose-built wall-mount enclosure in Vertiv's WDX line — 11U of rack space in a 24-inch-wide by 32-inch-deep footprint. When I specify this unit, the 32-inch depth is the deciding factor: it's the minimum you need to house full-depth 1U appliances (NVRs, managed PoE switches) without bending cables around the door frame.

Technical Highlights:

• 11U rack height: enough vertical space for a surveillance NVR, a PoE switch, a patch panel, and a 1U UPS — the four components that make up most compact security head-ends — with one or two spare units for future expansion.
• 24W × 32D interior: the 32-inch depth is a meaningful spec; enclosures shallower than 30 inches force you into short-depth or half-depth equipment that narrows your vendor options and often costs more.
• Black finish (B suffix): appropriate for finished-space installs — retail back offices, corporate lobby closets, school hallways — where a grey enclosure reads as an afterthought.

Deployment Considerations:

• Wall-mount load capacity is not confirmed in available evidence — always pull the Vertiv WDX series datasheet and verify the rated load against your heaviest populated configuration before drilling into drywall or CMU block.
• At 11U, this enclosure is tight if you later add a second NVR or redundant switch. Size up to a larger WDX variant from the outset if your camera count is expected to grow past 32 channels.

Best fit: small-to-midsize surveillance deployments — retail stores, branch offices, school wings — where a floor-standing cabinet is impractical and a clean, secure wall-mount head-end is the right call.