Ubiquiti UACC-CABLE-PATCH-OUTDOOR-C6A-5M-W Shielded Outdoor Patch Cable
The Ubiquiti UACC-CABLE-PATCH-OUTDOOR-C6A-5M-W is a Category 6A shielded patch cable purpose-built for outdoor network deployments where environmental stress rules out standard interior cabling. This cable handles the full 10 Gigabit Ethernet bandwidth rating, meaning it won't become a bottleneck when connecting enterprise wireless access points, mesh network nodes, or hardened surveillance infrastructure across exposed rooftops, tower sites, or perimeter fencing.
Key Features
- 10 GbE Certified (Cat6A): Supports full 10 Gigabit Ethernet throughput end-to-end — eliminates bandwidth concerns when deploying high-density access points or point-to-point microwave links that require low-latency, high-capacity backhaul.
- Shielded Construction: Foil and braid shielding reduces electromagnetic interference in environments with dense RF equipment, generators, or power distribution infrastructure — critical when cable runs must cross or run parallel to high-voltage lines.
- Outdoor-Rated Jacket: UV-stabilized polymer shell resists degradation from direct sunlight, preventing brittleness and insulation failure over 3–5 years of continuous exposure — indoor cables degrade to complete failure in 18–24 months under the same conditions.
- Temperature Resilience: Rated for extreme temperature swings typical of unheated equipment shelters and outdoor cabinets; maintains signal integrity in both sub-zero and high-heat environments without connector corrosion or copper oxidation.
- Moisture & Corrosion Resistance: Polymer jacket and shielding prevent water ingress and salt-air corrosion, extending service life in coastal deployments or high-humidity zones where standard cables fail prematurely.
- 5-Meter Length: Bridges gaps between tower-mounted equipment, outdoor PoE injectors, and network switches without requiring intermediate patch panels or splicing — each splice introduces signal loss and failure points in high-speed links.
Integration and Deployment Context
This cable integrates with any standard RJ45 port on Ubiquiti networking equipment and third-party Category 6A infrastructure. Ideal for outdoor wireless mesh networks, telecom point-to-point radio links, and security camera backbone networks where weather exposure is unavoidable. When paired with outdoor PoE switches and hardened access points, it forms part of a cohesive system that survives freeze-thaw cycles, salt spray, and UV weathering without performance loss.
The shielding also matters in RF-dense environments — near cellular transmission sites, microwave links, or broadcast antennas. Unshielded cabling in such locations can pick up significant interference, degrading or dropping connections intermittently. The UACC-CABLE-PATCH-OUTDOOR-C6A-5M-W (often searched as UACC CABLE PATCH OUTDOOR C6A 5M W) eliminates that risk.
When to Consider Alternatives
If your deployment is entirely indoors, standard Cat6A cabling costs less and is easier to source. If runs exceed 5 meters and you want to avoid intermediate connections, consider custom-length outdoor cables. If you require pre-terminated connectors with weatherproof boots, verify RJ45 connector specifications against your termination standards.
Frequently Asked Questions
Q: Is this cable suitable for direct burial or submersion?
A: No. This cable is outdoor-rated for above-ground exposure (UV, rain, temperature extremes). Direct burial requires armored or conduit-protected cable rated for underground service. Submersion requires cable rated for wet environments — consult the datasheet for specific depth/duration limits.
Q: Will this cable work with non-Ubiquiti equipment?
A: Yes. It is a standard Cat6A shielded patch cable and will connect any equipment with RJ45 ports. No vendor-specific firmware or drivers are required.
Q: What is the maximum run length for 10 GbE performance?
A: Cat6A supports 10 Gbps up to 55 meters (180 ft) under ideal conditions. At 5 meters, this cable will deliver full rated speed with negligible signal loss.
Q: Can I use this indoors?
A: Yes, but it is overkill for interior installations. Standard indoor Cat6A is cheaper and adequate. Reserve this cable for outdoor runs where UV and moisture resistance are required.
Q: Does this cable include weatherproof RJ45 connectors?
A: The cable itself has a weather-resistant jacket. RJ45 connector weatherproofing depends on the specific termination — verify connector specifications separately if operating in direct spray environments.
Q: Is this cable PoE-compatible?
A: Yes. Cat6A shielding and conductors support all PoE variants (802.3af, 802.3at, 802.3bt). No restrictions on power delivery.
James EverettPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The UACC-CABLE-PATCH-OUTDOOR-C6A-5M-W is a cable that solves a specific and painful problem: standard Cat6A fails outdoors within 18–24 months, forcing you to replace it repeatedly and lose uptime during maintenance windows. This cable's UV-stabilized jacket and shielding eliminate that cycle for outdoor mesh nodes and wireless backhaul links.
Technical Highlights:
- 10 GbE Cat6A Rating: Delivers full 10 Gbps bandwidth over 5 meters with headroom to spare — no bottleneck on high-density access point clusters or point-to-point microwave links feeding traffic back to your NOC.
- Shielded Construction (Foil + Braid): Cuts electromagnetic coupling in RF-dense sites by 15–20 dB compared to unshielded Cat6A — meaningful when cables run near cellular towers, broadcast antennas, or dense microwave links where interference is a daily problem.
- UV-Stabilized Polymer Jacket: Withstands direct solar exposure for 5+ years before degradation, compared to 18–24 months for standard interior-rated cables — eliminates unscheduled replacements and the risk of intermittent connection loss due to jacket brittleness.
Deployment Considerations:
- Not rated for direct burial or continuous submersion — this is above-ground outdoor only. If you need underground runs, upgrade to armored cable or run it through rigid conduit.
- The 5-meter fixed length means you cannot splice mid-run without introducing signal loss and a failure point. Plan cable routes to avoid splices on high-speed links.
- RJ45 connector weatherproofing is separate — the cable jacket is weather-resistant, but your terminations need individual consideration. If installing near salt spray or direct rain impact, specify weatherproof RJ45 boots or sealed panel connectors.
Deploy this cable on outdoor wireless mesh backhaul, tower-to-shelter interconnects, and perimeter camera system backbone runs where replacement cycles and intermittent connection loss are too costly to tolerate. It is the right choice for RF-dense sites and weather-exposed installations where signal integrity and durability outweigh cost.
