Pelco UEBWAA Wall Bracket for ULISSE EVO PTZ Camera
The UEBWAA is a purpose-built wall-mounting bracket designed exclusively for the Pelco ULISSE EVO PTZ camera series. Unlike generic camera brackets, this accessory is engineered to handle the dynamic stresses inherent to pan-tilt-zoom operation—continuous center-of-gravity shifts, inertial loading during rapid pan and tilt movements, and environmental wind forces that shift during motion cycles. This specialization matters: a fixed-camera bracket will fail under PTZ duty cycles because it's designed for static loads only.
Key Features
- PTZ-Rated Structural Design: Supports full ULISSE EVO camera body weight plus dynamic loads generated during continuous pan/tilt operation—not a generic mount repurposed for PTZ duty.
- Direct Wall-Surface Installation: Mounts to concrete or structural steel substrates that can bear combined weight of camera, dynamic PTZ stress, and environmental wind loading. Wall mounting works best on solid building facades and structural elements; parapet-edge or rail-mounted installations should use the UEBP0AA bracket instead.
- Integrated Cabling Route: Built-in conduit and cable-management paths for power and communications wiring eliminate exposed runs and reduce installation time on vertical surfaces.
- RAL9002 Gray-White Finish: Matches standard ULISSE EVO camera body color for visual continuity—reduces visual clutter on building elevations and eliminates the need for paint matching on new installations.
- NDAA Section 889 Compliance: Meets U.S. defense and government procurement requirements, enabling deployment on federal projects and GSA schedule bid work without additional compliance vetting.
- ULISSE EVO Series-Specific: Compatible exclusively with ULISSE EVO PTZ cameras; not backward compatible with earlier Pelco PTZ platforms. Verify camera model before ordering to avoid mounting interference or improper load distribution.
Installation Context
Substrate selection is critical. Wall mounting requires concrete, brick, or structural steel capable of accepting expansion anchors or bolts and distributing the combined static load plus dynamic pan/tilt stress. Verify substrate thickness and anchor specifications in your installation design. For buildings with thin curtain walls, composite facades, or parapet installations, use Pelco's UEBP0AA parapet bracket instead. Wind loading calculations should account for camera profile and local building codes (IBC, local amendments). A 5–10 mph dynamic gust during full-speed pan can amplify loads significantly on lightweight mounting substrates.
Integration with PTZ camera Systems
This bracket is a mounting interface only and does not affect video codec, resolution, network connectivity, or control protocol. It works with all network video recorders and video management systems compatible with ULISSE EVO cameras. Ensure power and data cabling (typically PoE or coaxial) routes cleanly through the bracket's cable paths before final installation.
Support and Warranty
Backed by a 1-year manufacturer warranty covering structural defects, finishing, and material failure. Support is available through Pelco's global service network and authorized integration partners.
Frequently Asked Questions
Q: Can I use the UEBWAA on non-ULISSE EVO Pelco PTZ cameras?
A: No. The UEBWAA is engineered for ULISSE EVO PTZ cameras only. Mounting interfaces, load-bearing geometry, and cable routing are specific to this camera series. Using it on other Pelco PTZ models risks improper weight distribution and structural failure.
Q: What substrate types are suitable for UEBWAA installation?
A: Concrete and structural steel that can support combined static load, dynamic PTZ stress, and environmental wind forces. Verify substrate thickness and fastener specifications with your structural engineer before installation.
Q: Does the UEBWAA bracket come with fasteners?
A: The bracket itself includes integrated mounting points. Fasteners (expansion anchors, bolts, washers) must be selected based on your specific substrate and local building code requirements. Consult the ULISSE EVO installation guide for anchor specifications.
Q: Is the UEBWAA NDAA Section 889 compliant?
A: Yes. The bracket meets NDAA Section 889 requirements for government and defense installations.
Q: What finish is the UEBWAA bracket, and will it match my camera body?
A: RAL9002 gray-white finish matches the standard ULISSE EVO camera body color for aesthetic continuity on building facades.
Q: Is there a parapet-mount alternative if my installation is not wall-surface?
A: Yes. For parapet-edge or rail installations, Pelco offers the UEBP0AA bracket as an alternative mounting solution.
Marty AllisonPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The UEBWAA bracket is not a commodity part—it's application-specific hardware engineered to absorb the dynamic stresses that kill generic camera mounts in PTZ service. The key differentiator is its ability to handle continuous center-of-gravity shifts during pan and tilt cycles, which introduce lateral and inertial loading that static-mount design specifications ignore entirely. This is why pairing the UEBWAA with your ULISSE EVO PTZ installation ensures the camera stays mounted and level under 24/7 motion duty.
Technical Highlights:
- Dynamic Load Rating: Engineered to support full ULISSE EVO camera body weight plus continuous pan/tilt stress cycles—not just static load. A generic wall bracket rated for a fixed camera's weight will loosen, shift, or fail within weeks under PTZ operation.
- Integrated Cable Management: Built-in routing paths for power and control wiring eliminate exposed cable sag and routing improvisation on building facades. Clean cable paths also reduce wind-load multiplication that occurs with dangling runs.
- RAL9002 Finish Continuity: Gray-white color matching reduces visual clutter and eliminates field-paint touch-ups—a small detail that matters on government and enterprise campuses where appearance standards are non-negotiable.
Deployment Considerations:
- Substrate is Non-Negotiable: UEBWAA performance depends entirely on concrete or steel substrate rated for dynamic loads. Thin curtain walls, composite facades, or lightweight panels will transfer stress to building structure unpredictably. Always have a structural engineer verify substrate adequacy before installation.
- Wind Loading Multiplier: A 10 mph gust during full-speed PTZ pan amplifies effective load on the bracket by 2–3× static load. Account for this in substrate and fastener selection, and verify local IBC amendments for wind exposure.
- ULISSE EVO-Only Fit: This bracket is not compatible with other Pelco PTZ families. Verify camera model before purchasing to avoid a second site visit.
Deploy this bracket on concrete or structural-steel building facades where ULISSE EVO PTZ coverage needs to move continuously over wide angles. Substrate validation and proper fastener selection are non-negotiable—cut corners on either, and you're buying a repeat service call.
