Panduit FZ2RPU1U1ONM005 Opti-Core OM4 LC Uniboot Fiber Patch Cord
The Panduit FZ2RPU1U1ONM005 Opti-Core patch cord delivers factory-terminated OM4 multimode performance in a space-saving uniboot form factor designed for high-density 40 and 100 Gigabit Ethernet deployments. This 5-meter plenum-rated cable features duplex LC uniboot connectors with integrated pull-boot polarity reversal, 50/125-micron OM4 fiber optimized for insertion loss below 0.35dB, and aqua OFNP jacketing that meets NEC Article 770 requirements for installation in air-handling spaces without conduit. Engineered for data center horizontal distribution, storage network fabrics, and cassette-based pre-terminated systems, it supports 40GBASE-SR4 and 100GBASE-SR4 applications up to 150 meters while reducing cable congestion by 50% compared to traditional duplex LC patch cords.
Key Features
- OM4 50/125μm laser-optimized multimode fiber supports 40GBASE-SR4 up to 100m and 100GBASE-SR4 up to 150m per IEEE 802.3ba
- LC duplex uniboot connector with pull-boot mechanism enables A-to-B polarity conversion in seconds without re-termination
- Optimized insertion loss below 0.35dB typical provides link budget margin for 40/100G transceiver sensitivity and aging headroom
- Plenum OFNP flammability rating (UL 1666) for installation in ceiling plenums, raised floors, and HVAC ductwork per NEC 770.179
- 5-meter (16.4 ft) length suits rack-to-rack connections in row-based data center architectures and entrance facility cross-connects
- Aqua jacket color per TIA-598-C Appendix A for rapid OM4 identification in mixed-mode fiber plants
- Factory-terminated and tested to TIA-568-C.3 and ISO/IEC 11801 for consistent sub-0.35dB insertion loss and RoHS compliance
The FZ2RPU1U1ONM005's uniboot design solves the cable management crisis in 40 and 100 Gigabit Ethernet installations where port density doubles or quadriples compared to 10G deployments. Traditional duplex LC patch cords create two separate 2.5mm connector bodies per link, consuming horizontal and vertical pathway space that forces oversized cable managers and blocks airflow in front-to-rear cooling designs. Panduit's single-body uniboot connector reduces the physical footprint by approximately 50%, allowing tighter bend radii around vertical cable managers and improved lane organization in high-density switch fabrics. The integrated pull-boot polarity mechanism is the critical advantage: pulling the boot back exposes the duplex fiber pair, which rotates 180 degrees to swap transmit and receive paths without field re-termination or polarity adapter modules. This eliminates the Method A/B/C confusion in ANSI/TIA-568-C.0 Annex B during cassette-based deployments, where MPO backbone trunks break out to LC duplex interfaces and polarity mismatches typically require costly adapter panels or re-pulls. Insertion loss is held below 0.35dB through Panduit's factory termination process, which uses automated cleaving, epoxy-less mechanical splice termini, and interferometric end-face inspection to eliminate the 0.5–0.75dB variability common in field-terminated assemblies. On 100GBASE-SR4 links with 1.9dB receiver sensitivity and 2.4dB total channel budget per IEEE 802.3ba Table 86-11, the 0.15–0.2dB margin gained by sub-0.35dB connectors translates to longer service life before aging-related bit error rate degradation forces optics replacement.
Deploy the FZ2RPU1U1ONM005 in data center horizontal runs connecting top-of-rack switches to aggregation or spine switches within the same row, typically 3–10 meters in row-based architectures. The 5-meter length is also standard for storage area network fabrics linking blade servers to Fibre Channel or FCoE switches, where uniboot's reduced diameter improves airflow in densely packed chassis environments. In cassette-based pre-terminated systems, use this patch cord as the equipment cord connecting LC duplex switch ports to the front side of MTP-to-LC breakout cassettes in fiber enclosures; the uniboot pull-boot lets you correct polarity in the field if your cassette follows Method B (key-up to key-down) but your switch optics expect Method A (key-up to key-up). For entrance facility and telecommunications room cross-connects, the plenum OFNP rating satisfies NEC 770.179(A) requirements for cables installed in environmental air spaces without raceway, eliminating the cost of EMT conduit or plenum-rated cable tray in ceiling grid installations. The aqua jacket follows TIA-598-C Appendix A color coding for OM4 multimode fiber, preventing accidental cross-connection with OM3 (aqua), OM2 (orange), or single-mode OS2 (yellow) fibers during moves, adds, and changes. In 40GBASE-SR4 parallel optics, where four fiber pairs share a single QSFP+ transceiver, the color-coded uniboot jacket combined with numbered connector boots (if field-labeled) speeds troubleshooting when one of four lanes shows high BER.
Panduit Opti-Core factory termination removes the insertion loss variability and end-face geometry failures that plague field-terminated assemblies, with every connector tested to meet TIA-568-C.3 performance levels and IL/RL recorded in Panduit's QA database. The uniboot design delivers the cable density and polarity flexibility required for 40/100G server fabrics while maintaining full backward compatibility with standard LC duplex transceivers and patch panels, so you can migrate from 10GBASE-SR to 40GBASE-SR4 without infrastructure replacement. This 5-meter plenum-rated assembly fits the 3–7 meter sweet spot for row-based data center horizontal distribution, meets NEC Article 770 and NFPA 90A air-handling space requirements without conduit, and provides the insertion loss margin and polarity control that protect 40/100G optics warranties in TIA-942 and ISO/IEC 11801-compliant structured cabling systems.
