Panduit FZ2RLU1U1NNM9.5 OM4 LC Uniboot Duplex Fiber Patch Cable

The Panduit FZ2RLU1U1NNM9.5 is a 9.5-meter (31-foot) OM4 multimode duplex fiber patch cable engineered for high-speed 10/40/100GBASE-SR datacenter and enterprise network deployments. It features LC Uniboot connectors on both ends with integrated pull-boots, a 2.0mm LSZH-jacketed duplex cable, and ultra-low insertion loss performance. The Uniboot design cuts patch-panel footprint in half compared to traditional duplex LC cables while enabling tool-free polarity reversal in the field. LSZH construction meets plenum fire-safety requirements for enclosed cable pathways. This length is ideal for cross-connect applications, intra-rack patching in deeper cabinets, and short horizontal runs where standard 3-meter cables fall short.

Key Features

• OM4 50/125 micron laser-optimized multimode fiber supports 10GBASE-SR to 400m, 40/100GBASE-SR4 to 150m
• LC Uniboot connectors with pull-boots reduce cable congestion by 50% vs. traditional duplex LC
• Tool-free polarity reversal via internal push-tab mechanism—no re-termination required for A-to-B or B-to-A configurations
• Ultra-low insertion loss (typically <0.15 dB) minimizes link budget impact in multi-tier architectures
• LSZH (Low Smoke Zero Halogen) 2.0mm duplex jacket complies with IEC 60332-1 and IEC 60754 for enclosed-space safety
• Aqua-colored boot and jacket for instant OM4 identification per TIA-598-D color standards
• Pre-terminated and factory-tested to exceed TIA-568.3-D and IEC 61753 performance requirements
• 9.5-meter length accommodates intra-rack, cross-connect, and short horizontal patching scenarios

OM4 fiber is the standard for modern 40G and 100G SR optics in datacenter and campus backbones. Its 50-micron core and optimized modal bandwidth (≥4700 MHz·km at 850nm) enable reliable transmission over distances that meet most intra-building requirements without stepping up to single-mode infrastructure. The FZ2RLU1U1NNM9.5 uses precision-polished LC connectors with factory-installed pull-boots that protect the connector body during installation and provide a non-slip grip during removal—critical when working in densely populated patch panels where finger access is limited. Insertion loss is held to ultra-low thresholds (typically ≤0.15 dB per mated pair), which matters in cascaded architectures where you're patching through multiple panels or switches. The cable's 2.0mm duplex construction balances flexibility for tight-radius routing with enough stiffness to prevent kinking in vertical cable managers. LSZH jacketing is non-PVC, producing minimal smoke and no halogenated acids when exposed to fire—a requirement in most occupied-space plenum pathways and international installations governed by IEC standards.

Uniboot LC cables solve a persistent problem in high-density patching: real estate. A traditional duplex LC cable occupies two connector positions and creates a bulky loop at the back of the panel; the Uniboot design consolidates both fibers into a single-width connector housing, effectively doubling port density in the same 1U panel. The polarity-reversal feature is a field lifesaver—push the internal tab, rotate the boot 180°, and you've swapped transmit/receive paths without pulling a new cable or re-terminating. This is useful when adapting to different transceiver standards or correcting polarity mismatches during troubleshooting. At 9.5 meters, this cable bridges the gap between short 3-meter intra-rack jumpers and longer 15+ meter horizontal runs; it's the right length for patching across adjacent racks, running from a core switch to a patch panel in the same row, or connecting equipment in deeper cabinets where the distance from front-mounted patch panel to rear-mounted switch exceeds what a 5-meter cable can comfortably span.

This cable is factory-terminated and tested to TIA-568.3-D and IEC 61753-1, with full end-face geometry inspection and insertion/return loss validation before it ships. Panduit's quality control ensures that each connector meets the physical-contact polish standards required for low back-reflection and reliable mating with precision-aligned transceivers. The pull-boot design distributes pull force away from the fragile ferrule, reducing the risk of end-face damage during installation or moves-adds-changes. For integrators managing compliance-driven deployments, the LSZH jacket carries IEC 60332-1 flame-propagation and IEC 60754-1/2 halogen-content certifications, which satisfy European EN 50575 CPR and are increasingly required in U.S. federal and healthcare facilities.