Vertiv I10112 Metered Upgradeable 1U Horizontal rPDU
Overview
The Vertiv I10112 is a 1U horizontal rack PDU rated at 20A/120V (1.9kW) with 10 NEMA 5-20R receptacles and a local LED display for real-time input current monitoring. Designed for data center racks and server cabinets where power visibility matters but full network-based monitoring isn't yet required, the I10112 fits squarely in the PowerIT Upgradeable rPDU family — meaning you can add network-level monitoring later via a hot-swap Interchangeable Monitoring Device (IMD) without replacing the unit. That upgrade path makes it a practical choice for staged deployments where budget or network complexity doesn't justify full monitoring on day one.
The model number MN01D1R0-10D203-2TL5A0H10-S defines the full configuration: 20A input, 10-outlet rear duplex layout, 10ft L5-20P twistlock cord, black powder coat finish. Every unit ships 100% factory-tested before leaving the production line.
Key Features
- Metered Input with Local LED Display: The scrolling digital display shows real-time kWh, Watts, VA, Power Factor, Volts, and Amps at 1% accuracy (ANSI C12.1 / IEC 62053-21 compliant). For technicians working in the rack, that means no need to pull up a management interface to check current draw during a server swap or migration — the number is right there on the front.
- Hot-Swap Upgradeable to Monitored: The IMD slot means this unit can be converted to a network-monitored rPDU at any point without swapping hardware. If your facility management requirements evolve — DCIM integration, remote alerting, per-outlet scheduling — the upgrade path is a single add-on component, not a forklift.
- 10x NEMA 5-20R Duplex Receptacles: Ten 20A-rated outlets in a duplex rear configuration give you flexibility for mixed 1U/2U server and networking gear. NEMA 5-20R accepts both standard 5-15 plugs and 20A 5-20 plugs, so most rack-mount equipment connects without adapters.
- NEMA L5-20P Twistlock Input: The L5-20P locking plug on the 10ft/3m, 12/3 AWG power cord locks securely into the UPS or PDU feed, eliminating accidental disconnection under vibration or cable congestion. Rear power entry keeps the front of the 1U chassis clean in tight rack environments.
- 1U Horizontal, 19-Inch Chassis with Adjustable Mount Brackets: At 1.72in x 17in x 8.5in, the I10112 mounts in any standard 19-inch rack. Adjustable brackets accommodate varying rail depths without additional hardware purchases — a real time-saver in mixed-rack environments.
- TAA Compliant, Buy American Act COTS Compliant, Made in USA: Manufactured domestically and fully TAA compliant — clears the procurement gate for federal agencies, defense contractors, and government-funded facilities without a compliance waiver. Also RoHS and FCC Part 15 Class A certified, and UL/c-UL Listed to 62368-1.
- 1.9kW Load Capacity at 120V: The 20A circuit derated to 1.9kW (per NEC 80% continuous load rule) is correctly sized for a half-populated 1U server rack or a networking equipment cabinet running switches and patch panels. Attempting to load beyond this on a continuous basis trips the upstream breaker — plan your load distribution before deployment.
- Maximum Operating Temperature of 60°C / 140°F: Rated for hot-aisle temperatures that exceed what most IT equipment tolerates. In a properly contained hot/cold aisle, the rPDU won't be the limiting factor even in high-density environments.
- 5-Year Limited Warranty: Vertiv backs the I10112 with a 5-year limited warranty — longer than the typical 2–3 year window on comparable units, which matters for assets that rarely get cycled out on a short hardware refresh schedule.
Integration and Compatibility
The I10112 integrates into any rack environment using standard 19-inch mounting. The rear power entry and rear-facing receptacles support front-to-back cable management in hot/cold aisle containment setups. As a metered-only unit, it does not require network connectivity — power is the only connection needed. When upgrading to monitored via IMD, the unit gains Ethernet-based SNMP/web interface access compatible with most DCIM platforms; consult the IMD spec sheet for supported protocols and compatibility details. The unit draws from a single L5-20P source, so confirm your UPS or PDL feed has an available L5-20P receptacle before mounting.
For facilities running Vertiv power infrastructure or pairing with Vertiv UPS systems, the L5-20P input plugs directly into matching receptacles on Liebert GXT and similar UPS families. Browse the full rack PDU category to compare horizontal vs. vertical configurations or higher-amperage options. If your deployment requires per-outlet switching or outlet-level monitoring, review the power distribution planning resources before specifying this unit — the I10112 provides input-level metering only, with no per-outlet measurement or switching in the base configuration.
Organizations running mixed-voltage environments should note this unit is strictly 100–120V. For 208V or 240V rack power, a separate model in the Vertiv PowerIT line is required. The metered PDU selection guide covers voltage, amperage, and form factor tradeoffs across the full lineup.
Frequently Asked Questions
Q: Is the Vertiv I10112 TAA compliant?
A: Yes. The I10112 is manufactured in the USA and is TAA Compliant and Buy American Act COTS Compliant, making it eligible for federal government procurement without a waiver.
Q: Can the I10112 be upgraded to a network-monitored PDU later?
A: Yes. The I10112 belongs to the Vertiv PowerIT Upgradeable rPDU family and accepts a hot-swap Interchangeable Monitoring Device (IMD) that converts it to a networked, monitored rPDU without replacing the unit.
Q: What is the warranty on the I10112?
A: Vertiv covers the I10112 with a 5-year limited warranty.
Q: What plug type does the I10112 use on the input cord?
A: The I10112 ships with a NEMA L5-20P twistlock plug on a 10ft (3m), 12/3 AWG power cord. The L5-20P locks into the upstream power source to prevent accidental disconnection.
Q: How many outlets does the I10112 have, and what type?
A: The I10112 has 10 NEMA 5-20R receptacles configured in a duplex rear layout. NEMA 5-20R accepts both standard 5-15 and 20A 5-20 plugs.
Q: What safety certifications does the I10112 carry?
A: The I10112 is UL and c-UL Listed to 62368-1, RoHS Compliant, and FCC Part 15 Class A Conformance listed.
The I10112 is one of those units I recommend specifically when a client wants to avoid paying for monitoring they don't need yet but refuses to back themselves into a corner on the upgrade path. The hot-swap IMD slot is the reason — you get a metered rPDU at a metered price point, and when the facility management team eventually asks for SNMP visibility or DCIM integration, you add the IMD rather than pulling and replacing 10 PDUs across a row of racks.
Technical Highlights:
- ANSI C12.1 / IEC 62053-21 Metering at 1% Accuracy: This isn't a rough estimate — it's calibrated power measurement. Knowing you're at 16.2A instead of 'somewhere around 15–17A' is the difference between confident capacity planning and guesswork when adding another server to the rack.
- 12/3 AWG, 10ft L5-20P Twistlock Cord: The 12-gauge wire is correctly sized for a sustained 20A draw, and the twistlock connector eliminates the leading cause of unplanned outages in active cabinets — someone snagging a cord during maintenance. The 10ft run gives enough slack to reach a UPS in a standard 42U floor cabinet without a cord extension.
- 60°C / 140°F Max Operating Temperature: Most rack-mount gear throttles or shuts down well below this. The rPDU won't fail in a hot aisle containment scenario even if airflow management is imperfect — it outlasts the servers it feeds.
Deployment Considerations:
- Confirm your upstream UPS or power strip has an available NEMA L5-20P receptacle before mounting. The twistlock input is non-negotiable on this unit — you cannot substitute a standard 5-20P cord without an adapter, and adapters defeat the purpose of the locking connector.
- The 1.9kW continuous load ceiling (NEC 80% of 20A) is real. If your rack has multiple high-draw servers with dual PSUs, calculate actual draw before specifying this unit — you may need a 30A circuit and a different model in the PowerIT family.
This unit earns its place in federal data centers, co-location cabinets, and enterprise server rooms where TAA compliance is a procurement requirement and the team wants a credible monitoring upgrade path without a forklift refresh. It's the right starting point for a staged build-out where rack density and monitoring requirements will evolve over the next few years.
