Panduit TFC10WH-X LD10 Surface Raceway T-Fitting, White, 10-Pack
Overview
The Panduit TFC10WH-X is a white PVC T-fitting from the Pan-Way™ surface raceway line, designed to branch cable runs at a 90° T-junction within LD10 and LDPH10 raceway channels. When a single horizontal cable run needs to split — feeding a wall outlet, a reader, or a camera drop point — this fitting keeps the transition clean, protected, and code-compliant rather than relying on open wire or improvised cuts. Sold in packs of 10 (TFC10WH-X, sometimes searched as TFC10WH X), it suits contractors completing multi-drop runs in a single trip.
The fitting handles 1-inch bend radius control within the Pan-Way™ system, a practical spec when routing Cat6 or low-voltage security cabling around corners without exceeding the cable's minimum bend radius — a silent cause of attenuation problems that only show up after commissioning.
Key Features
- T-Branch geometry: Extends cable runs in a T-configuration, so a single horizontal raceway can branch to a device outlet or junction box without exposed wire or field-fabricated fittings. This matters on retrofit installs where clean aesthetics are required by facility management.
- Hinged one-piece design: The single-piece hinged construction snaps closed over existing cable, meaning you can add a branch point to an already-wired run without pulling cable back through — a real time saver on occupied facilities.
- Integrated adhesive backing: Adhesive mounting eliminates screw-per-fitting labor on drywall and painted concrete block, typical wall surfaces in commercial interiors. Combine with mechanical fasteners on high-traffic runs.
- PVC construction, UL94V-0 rated: UL94V-0 is a self-extinguishing flame rating — the material stops burning when the ignition source is removed. On plenum and wall-penetration runs, this satisfies the fire-safety requirement without upgrading to metal raceway.
- UL5A listed + TIA/EIA compliant: UL5A covers non-metallic surface raceways for electrical wiring; TIA/EIA compliance confirms suitability for structured data cabling. Both are inspection-pass requirements on commercial security installs — specify this fitting and you're covered on both the electrical and low-voltage inspections.
- FT4 (CSA) flame rating: Adds Canadian Standards Association flame compliance for cross-border projects or facilities with CSA inspection requirements.
- Compact cross-section (1.62" W × 0.93" H): At 41.1mm wide and 23.6mm tall, the fitting sits flush against the wall surface without protruding into door clearances or ADA strike zones — relevant on corridor installs near door frames.
- White finish, 4.73" overall length: Matches standard white LD10 raceway channel for a continuous appearance. The 4.73-inch body gives enough straight run on each arm to seat the adjoining raceway sections without gaps.
- Pack quantity of 10, carton of 50: The 10-unit pack aligns with typical per-room or per-zone material pulls; the 50-unit carton suits full-floor or multi-zone projects without overstocking fittings at individual work orders.
Integration & Compatibility
The TFC10WH-X is specifically designed for use with Panduit LD10 and LDPH10 single-channel surface raceway. It is not cross-compatible with wider or narrower Pan-Way™ profiles (such as LD3 or LD5) — verify the raceway channel width before ordering. The adhesive and fitting geometry are matched to the LD10 channel's 1.62-inch interior, so substituting a different channel will result in a misfit joint. For wire management projects using other Pan-Way™ raceway widths, consult the Panduit catalog for the corresponding T-fitting SKU in that profile family.
This fitting is appropriate for low-voltage cabling runs including Cat5e/Cat6 data, security camera drops, access control wiring, and similar structured cabling applications. It is not rated for high-voltage power conductors beyond the UL5A classification limits — confirm conductor ratings with your AHJ on mixed power/data raceway installs.
What's in the Box
- 10× Panduit TFC10WH-X T-fitting, white PVC (Pan-Way™ LD10/LDPH10 compatible)
Frequently Asked Questions
Q: What raceway channels is the TFC10WH-X compatible with?
A: The TFC10WH-X is designed for use with Panduit LD10 and LDPH10 single-channel surface raceway. It is not interchangeable with other Pan-Way™ profile widths.
Q: How many fittings are included per order?
A: Each unit sold is a pack of 10 fittings. The manufacturer carton contains 50 fittings (5 packs).
Q: What flame and safety ratings does the TFC10WH-X carry?
A: The fitting carries UL94V-0 (self-extinguishing), FT4 (CSA flame), is UL5A listed for non-metallic surface raceways, and meets TIA/EIA structured cabling standards.
Q: Does the TFC10WH-X use adhesive or screw mounting?
A: It includes integrated adhesive backing. For permanent or high-traffic installations, supplemental mechanical fasteners are recommended.
Q: What are the physical dimensions of the TFC10WH-X fitting?
A: Overall width is 1.62 inches (41.1mm), height is 0.93 inches (23.6mm), and length is 4.73 inches. The compact profile suits installs near door frames and in ADA-sensitive corridors.
Q: Is the TFC10WH-X suitable for data cabling as well as electrical wiring?
A: Yes. The UL5A listing covers electrical wiring, and TIA/EIA compliance confirms it meets structured data cabling standards — making it suitable for mixed security and data cable runs in a single raceway system.
The TFC10WH-X is the fitting I reach for when a low-voltage surface raceway run needs a branch point and I can't afford to have an AHJ pull my permit for a non-listed fitting. The UL5A listing and TIA/EIA compliance on this fitting mean you're covered on both the electrical and structured cabling sides of a commercial inspection — that combination is what separates a proper Pan-Way™ installation from a patch job.
Technical Highlights:
- UL94V-0 flame rating: Self-extinguishes when the ignition source is removed — satisfies fire-safety requirements on wall-surface cable runs without stepping up to metal raceway, which adds cost and labor on retrofit work.
- 1.62" × 0.93" cross-section: The compact 41.1mm × 23.6mm profile stays within door-frame clearances and below ADA strike-zone heights — a real constraint on corridor camera and access control drops that gets ignored until the facility manager flags it.
- Pack of 10, carton of 50: The 10-unit sell quantity aligns with per-zone material pulls; the 50-unit carton keeps project pricing manageable on multi-room or full-floor access control rollouts.
Deployment Considerations:
- Compatibility is LD10 and LDPH10 only — the fitting geometry is matched to the 1.62-inch interior of those channels. Bring the raceway profile number to the order, not just the brand name, or you'll be returning fittings.
- The adhesive backing is adequate for painted drywall on horizontal or vertical runs, but on textured masonry or in high-vibration environments (near HVAC equipment, loading dock walls), add a screw fastener at the center of the fitting body — the adhesive alone will walk over time.
This fitting is the right call on occupied commercial buildouts where camera and reader drops branch off a single horizontal raceway run — education facilities, healthcare corridors, and retail chains with repeat floor plans where you're pulling the same LD10 layout across dozens of rooms and need a T-branch that passes inspection the first time.
