Panduit QCRBCCB0001F032 Cat6 UTP Copper Trunk Cable 32ft

Overview

The Panduit QCRBCCB0001F032 is a 32-foot Category 6 unshielded twisted pair (UTP) copper trunk cable engineered for high-density structured cabling deployments in data centers, telecommunications rooms, and enterprise LAN backbones. Rated to 250 MHz and 1 Gbps, this pre-terminated trunk solution is built to TIA-568-C.2 and ISO/IEC 11801 standards and carries UL Listing — specifications that matter when your cabling plant needs to pass formal certification audits or satisfy insurance and code requirements. If you're building out a top-of-rack or end-of-row copper distribution scheme, the QCRBCCB0001F032 is sized at 32 feet to bridge typical intra-row or short cross-room runs without excess slack cluttering your pathway management.

Key Features

• 250 MHz Bandwidth: Category 6 performance headroom extends well beyond the 100 MHz minimum required for Gigabit Ethernet. That extra margin is not academic — it translates to better noise immunity and lower bit-error rates in dense cable environments where crosstalk pressure from adjacent cables is real. You get consistent 1 Gbps throughput, not theoretical.
• 1 Gbps Data Rate: Fully rated for Gigabit Ethernet (1000BASE-T), which remains the workhorse speed tier for IP cameras, VoIP endpoints, access control readers, and general enterprise LAN edge connections. The 32-foot trunk length keeps this a practical choice for row-to-row distribution without needing fiber uplinks.
• UTP (Unshielded) Construction: UTP eliminates the grounding requirements and termination complexity that come with shielded (STP/FTP) cable. In most data center and telecom room environments where the cable tray is not radiating interference, UTP is the right call — lower installed cost, faster termination, and no ground-continuity headaches.
• TIA-568-C.2 Compliance: This standard governs balanced twisted-pair cabling performance parameters including insertion loss, NEXT, and return loss. Compliance means the cable is independently verifiable against a published specification — critical for enterprise deployments that require channel certification using a Fluke DSX or equivalent tester.
• ISO/IEC 11801 Compliance: The international counterpart to TIA-568, ISO/IEC 11801 defines generic cabling for customer premises. Dual compliance (TIA + ISO) simplifies procurement for multi-national enterprises or projects with global facility standards that must satisfy both North American and international specs on the same cable plant.
• UL Listed: UL Listing indicates the cable has been evaluated by Underwriters Laboratories for safety. In many jurisdictions and for many commercial construction projects, UL Listed cable is a code requirement — not a preference. Specifying UL Listed cable up front avoids costly rework when an inspector requires documentation.
• Pre-Terminated Trunk Format: As a trunk cable, the QCRBCCB0001F032 arrives factory-terminated and ready to deploy — no field termination labor, no punch-down variability, no chance of a mis-wired pair introducing a link failure. In high-density rollouts where 10, 20, or 50 runs go in during a maintenance window, pre-terminated trunks are a significant time saver and improve first-pass certification rates.

Integration & Compatibility

The QCRBCCB0001F032 is designed for integration with Panduit's structured cabling ecosystem, including patch panels, outlets, and cable management systems that conform to TIA-568-C.2 and ISO/IEC 11801. As a standard Cat6 UTP trunk, it is also broadly compatible with third-party patch panels and connecting hardware that meet the same standard. Deploy it into existing copper cabling infrastructure without concern for proprietary interface requirements — the connector footprint follows industry-standard specifications.

For data center environments, this trunk pairs naturally with high-density patch panels and modular zone distribution frames. The 32-foot length is well-suited to top-of-rack switch connections to a nearby zone distribution point or intra-cabinet trunk routing. For environments where runs exceed 32 feet or where EMI is a concern (near unfiltered UPS systems, motor drives, or dense power cabling), evaluate a shielded Cat6A alternative or consider whether fiber is a better fit for the backbone segment — this UTP cable is the right tool for controlled, shorter copper runs in standard data center and enterprise networking environments.

When planning a multi-camera or multi-device IP deployment, pairing this cable with a PoE-capable network switch and a structured cable management system keeps your horizontal distribution clean and auditable from day one.

Frequently Asked Questions

Q: What is the maximum run length supported by the QCRBCCB0001F032?

A: The cable itself conforms to TIA-568-C.2 and ISO/IEC 11801 Cat6 performance standards, which define a maximum horizontal channel length of 100 meters (328 feet) including patch cord allowances. The QCRBCCB0001F032 is a 32-foot (approximately 9.75-meter) trunk segment, leaving substantial budget for patch cord and equipment cord lengths within the channel.

Q: Is the QCRBCCB0001F032 compatible with existing Cat5e infrastructure?

A: Cat6 UTP cable is backward-compatible with Cat5e connecting hardware at the physical connector level, but mixing Cat6 cable with Cat5e patch panels or outlets limits the channel to Cat5e performance. For the full 250 MHz bandwidth rating of the QCRBCCB0001F032 to be realized, all components in the channel — patch panels, outlets, and patch cords — should meet Cat6 specifications.

Q: Does the QCRBCCB0001F032 require any special grounding or shielding infrastructure?

A: No. The QCRBCCB0001F032 uses UTP (unshielded) construction, which does not require bonding to a ground plane or the use of shielded patch panels and outlets. This simplifies installation significantly in most data center and telecom room environments where interference from adjacent cabling is within normal parameters.

Q: Which standards does the QCRBCCB0001F032 meet?

A: The QCRBCCB0001F032 is compliant with TIA-568-C.2 (North American structured cabling standard), ISO/IEC 11801 (international generic cabling standard), and carries UL Listing for safety. These three credentials cover the primary compliance requirements for enterprise and data center structured cabling projects in North America and internationally.

Q: What data rates does the QCRBCCB0001F032 support?

A: The QCRBCCB0001F032 supports 1 Gbps (Gigabit Ethernet, 1000BASE-T) data rates, consistent with its Category 6 / 250 MHz rating. It is suitable for all standard Gigabit LAN applications including IP cameras, VoIP, access control, and general enterprise edge connectivity.