Panduit ACC19-A-M Adhesive Cord Clip for 0.19-Inch Cable

Overview

The Panduit ACC19-A-M is a single-conductor adhesive cord clip designed to route and retain cables up to 0.19 inches (4.8mm) in diameter on flat, clean surfaces without drilling or punching. The clip's pressure-sensitive foam tape backing bonds directly to the mounting surface, making it a practical choice for drop-ceiling infrastructure runs, wall-chased cable paths, and surface-mount conduit work where a permanent fastener would be overkill or simply unavailable. At a maximum supported load of 0.20 lbs (91g), the ACC19-A-M is sized for lightweight signal cables — think Cat5e/Cat6 patch runs, thin coax, or low-voltage control wiring — rather than heavy power bundles. For larger routing needs across structured cabling deployments, Panduit's broader ACC-series line covers additional cable diameters with rubber, acrylic, and high-bond adhesive variants.

Key Features

• Pressure-Sensitive Foam Tape Backing: The foam adhesive layer conforms slightly to surface texture, increasing contact area compared to a flat tape — useful on lightly textured drywall or painted metal surfaces where adhesion is otherwise inconsistent. No separate adhesive prep or primer required for clean, dry installations.
• 0.19-Inch (4.8mm) Cable Diameter Sizing: Sized specifically for common low-voltage signal cables in that 4–5mm outer-diameter range. A snug fit matters here — an oversized clip lets the cable rattle and eventually abrades against the clip edge. If your cable OD is significantly smaller, Panduit offers narrower clip models; if larger, step up to the next clip size in the ACC series.
• 0.20 lb (91g) Maximum Weight Rating: Keeps you honest about what this clip is designed to do. One clip is plenty for a single Cat6 patch drop; don't load it with a bundle of five cables expecting it to hold. For heavier bundled runs on cable management installations, use a dedicated bundling clip or mount rail.
• Tear-Tab Liner: The release liner extends past the clip edge to form a tab, so you can peel the backing with one hand while positioning the clip with the other — a small but real time-saver when you're working overhead or in a tight wall cavity with limited finger clearance.
• Adhesive Thickness of 0.04 Inches (1.0mm): Thin enough that it won't create a visible bump under a finished cable run, but substantial enough to absorb minor surface irregularities. On surfaces with heavy texture or contamination, the foam layer will not compensate — surface prep remains the installer's responsibility.
• No-Tool Installation: Peel, position, press. No drill bits, no anchors, no cable staples. That simplicity translates to faster installation cycles on high-count runs where every second per clip multiplies across hundreds of mounting points in a single cabinet row or cable tray tributary.
• Package and Color Variants Available: The -A-M suffix denotes this specific adhesive and color configuration. Panduit also offers rubber and acrylic adhesive variants as well as different package sizes under the same clip body — useful when environmental conditions (temperature cycling, UV exposure, high humidity) call for a different adhesive chemistry than standard foam tape.

Integration & Compatibility

The ACC19-A-M (often searched as ACC19 A M) is a passive mechanical component with no electrical or protocol considerations. Compatibility comes down to two factors: cable outer diameter and surface type. The 0.19-inch clip opening accommodates the outer jacket of most standard Cat5e, Cat6, RG59, and similarly sized low-voltage cables. Surface compatibility is governed by the pressure-sensitive foam tape — it bonds reliably to clean, dry painted drywall, metal raceway exteriors, plastic junction boxes, and smooth concrete. Porous, dusty, or oily surfaces will reduce adhesion significantly. For Panduit cable management systems that already use surface-mount raceways or J-hooks, these clips complement rather than replace structured mounting hardware, handling the final-meter tiedown where a raceway isn't practical. Pair with Panduit's cable ties or hook-and-loop straps for bundled runs where multiple cables share a clip anchor point.

Frequently Asked Questions

Q: What cable outer diameter does the ACC19-A-M accommodate?

A: The ACC19-A-M is sized for cables with a 0.19-inch (4.8mm) outer diameter. This covers most standard Cat5e, Cat6, RG59 coax, and similar low-voltage signal cables. If your cable OD is notably larger or smaller, select a different clip size from the Panduit ACC series.

Q: What is the maximum weight this clip can support?

A: The rated maximum load is 0.20 lbs (91g) per clip. This is appropriate for a single lightweight signal cable. Do not use a single clip to support heavy bundles or power cables exceeding this load rating.

Q: What type of adhesive does the ACC19-A-M use?

A: It uses a pressure-sensitive foam tape backing, 0.04 inches (1.0mm) thick. The foam layer improves contact on slightly textured surfaces. For environments with higher temperature cycling, UV exposure, or humidity, Panduit offers rubber and acrylic adhesive variants under the same clip body.

Q: What surfaces is the ACC19-A-M adhesive compatible with?

A: The pressure-sensitive foam tape bonds to clean, dry flat surfaces — painted drywall, metal, smooth plastic, and painted concrete are typical applications. Porous, dusty, oily, or wet surfaces will significantly reduce bond strength. Surface prep before installation is the installer's responsibility.

Q: Are other adhesive types or package sizes available for this clip?

A: Yes. Panduit offers rubber, acrylic, and high-bond adhesive suffix variants of the same clip body, as well as different package sizes and color options. The -A-M suffix identifies this specific configuration. Consult Panduit's current price sheet for the full variant list.

Q: Does the ACC19-A-M require any tools to install?

A: No tools are required. Peel the tear-tab liner (which extends past the clip edge for one-handed peeling), position the clip, and press firmly onto a clean dry surface. The extended tear-tab is specifically designed for easier installation in tight spaces or overhead applications.

Eden Phillips

The ACC19-A-M is one of those components that looks trivial until you're 200 clips into a cable tray tributary run and the tear-tab liner design has saved you 15 minutes of fumbling. The 0.04-inch foam tape layer is thicker than a flat adhesive pad but thin enough that finished runs don't show a visible bump — that matters in exposed cable paths where aesthetics count alongside function.

Technical Highlights:

• Foam Tape Adhesive (0.04 in / 1.0mm): Slightly compressible adhesive layer increases real contact area on textured painted surfaces versus a rigid tape — translates to better bond retention on lightly uneven drywall without needing a primer or surface treatment.
• 0.19-Inch Clip Opening: Purpose-matched to the 4–5mm OD range of standard Cat5e/Cat6 and RG59. A snug fit prevents cable migration inside the clip that causes abrasion on long runs under vibration or thermal cycling.
• 0.20 lb (91g) Load Rating: Explicit per-clip weight limit lets you engineer your mounting density correctly — don't exceed one lightweight cable per clip, and plan your clip spacing to keep cumulative cable weight distributed across enough anchor points to stay within spec.

Deployment Considerations:

• Surface contamination is the single largest failure mode for this clip. On construction sites or in occupied spaces, wipe the mounting surface with isopropyl alcohol and let it fully dry before pressing — even light finger oils from handling can reduce foam tape adhesion by 30–40% on non-porous surfaces.
• The -A-M standard foam tape is not rated for high-temperature or UV-exposed environments. If you're routing cables along exterior-facing walls, inside equipment rooms with significant heat cycling, or anywhere exposed to sunlight, verify that this adhesive chemistry suits the environment — Panduit's acrylic or high-bond suffix variants are the appropriate alternatives.

The ACC19-A-M is best suited for finished interior environments: clean server room cable drops, AV closet patch tiedowns, and low-voltage security cable runs where a drill isn't an option and the surface is controlled enough for foam tape to hold long-term. For outdoor, industrial, or high-vibration applications, specify the appropriate adhesive variant from the ACC series instead.