Panduit UTP6AX1M Cat 6A UTP Patch Cord 1m

Panduit UTP6AX1M TX6A 10Gig Cat 6A UTP Patch Cord

The Panduit UTP6AX1M is a 1-meter TX6A 10Gig Cat 6A UTP patch cord built for high-performance data center and enterprise network deployments. Constructed with 24 AWG solid copper conductors in a slim 6.4 mm (0.250") U/UTP design, this off-white cord delivers certified 10GBASE-T performance while maintaining dense patch panel organization. The integrated tangle-free latch streamlines moves, adds, and changes in high-turnover environments. RapidID pre-installed barcodes enable rapid asset tracking and port mapping through Panduit's documentation software, eliminating manual cable tracing during troubleshooting or audits. Ideal for server-to-switch patching, top-of-rack connectivity, and backbone aggregation where 10 Gb/s throughput and PoE++ delivery must coexist.

Key Features

• TX6A 10Gig Cat 6A certified — exceeds ANSI/TIA-568.2-D and ISO 11801 Class EA from 1-500 MHz
• 24 AWG solid copper U/UTP construction for 10GBASE-T Ethernet
• 1 meter (3.3 ft) length — optimal for server-to-ToR switch and in-rack patching
• Slim 6.4 mm diameter — 30% thinner than standard Cat 6A for high-density panel fill
• RapidID pre-installed barcode — pairs with Panduit asset management software for instant port mapping
• Tangle-free modular plug latch — prevents snags on adjacent cables during MACs
• Supports IEEE 802.3af/at PoE/PoE+ and 802.3bt Type 3 & Type 4 PoE++ (up to 90W)
• CM-rated jacket — suitable for horizontal runs within same floor
• Compatible with T568A and T568B wiring schemes
• Off-white jacket — maintains clean aesthetic in white-infra data centers

The UTP6AX1M achieves 10GBASE-T certification through 24 AWG solid copper conductors and unshielded twisted pair geometry optimized for alien crosstalk suppression. Unlike stranded-conductor patch cords that introduce insertion loss at high frequencies, Panduit's solid construction maintains channel performance margins across the full 500 MHz bandwidth. The U/UTP cable design eliminates the added diameter of shielded variants while still meeting Category 6A alien crosstalk limits through precise pair twist and separation. Each modular plug is factory-terminated with controlled pair untwist, ensuring less than 2.0 dB insertion loss and greater than 35 dB return loss at 500 MHz. This headroom matters when you're running 10GBASE-T over marginally-spec'd permanent link channels — the patch cord cannot be the weak link. The cord also supports 2.5GBASE-T and 5GBASE-T multi-gigabit rates for WLAN access point uplinks and surveillance NVR backhaul where 10G infrastructure exists but endpoints cap at 5G.

The RapidID barcode system addresses the documentation gap that plagues most data center MAC workflows. Each cord ships with a pre-printed barcode linking the cable ID to Panduit's RapidID software; scan the patch cord at installation, assign it to a port, and you've instantly created an as-built record without manual label printers or spreadsheet entry. During troubleshooting, scan the cord at the switch end to identify the far-end device and VLAN assignment — no tone generator required. The tangle-free latch uses a flexible boot that bends away from adjacent cables rather than hooking neighbors during extraction, cutting plug-replacement calls in half in high-density 48-port environments. At 6.4 mm diameter, the UTP6AX1M occupies 30% less cross-section than 8 mm Cat 6A shielded cords, allowing you to route 50% more cables through 2" horizontal cable managers without exceeding bend radius limits. The off-white jacket matches Panduit's Pan-Net cable plant and white patch panels for visual consistency in Tier III/IV data centers where aesthetics factor into audits.

The UTP6AX1M exceeds ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA transmission requirements across all 500 MHz test frequencies, ensuring compatibility with existing permanent link channels certified to the same standards. It also meets IEEE 802.3bt Type 3 and Type 4 PoE++ specs, delivering up to 90W per port for high-power devices like PTZ cameras, wireless access points, and thin clients without voltage drop concerns over the 1-meter run. Compliance with ANSI/TIA-1096-A (formerly FCC Part 68) and IEC 60603-7 guarantees interoperability with third-party patch panels and jacks from Leviton, CommScope, and Belden. The CM flammability rating qualifies the cord for horizontal runs within a single floor per NEC Article 800, though most integrators use it exclusively for equipment-to-panel patching where plenum rating isn't triggered. RoHS compliance simplifies procurement for European and California public-sector projects. For data center operators running converged 10G Ethernet and PoE++ on a unified Cat 6A plant, this cord closes the gap between structured cabling and active equipment with certified performance and built-in asset tracking that survives the first 100 MAC cycles.