Server Technology C1X24VT-5PPA17AC 0U Vertical 3-Phase Rack PDU

Overview

The Server Technology C1X24VT-5PPA17AC is a 0U vertical rack power distribution unit built for data center and server room racks that need high-density 3-phase power without eating into rack unit space. It's part of the Switched PRO1 Expansion series, delivering 24 individual IEC C13 outlets off a single 30A 3-phase feed — a fit for full-height server or network racks where every 1U or 2U of front rail space is committed to equipment, not power gear. C1X24VT-5PPA17AC mounts vertically in the rear channel of the rack, keeping outlet access clear of cable managers and PDU brackets that would otherwise compete with U space.

Key Features

• 24x IEC C13 Outlets: Enough outlet count to power two dozen servers, switches, or other C14-corded devices from one strip — cuts down on daisy-chained power strips and the cable clutter that comes with them.
• 17.3kW Total Power Capacity: Sized for dense server or network racks running multiple high-draw chassis simultaneously, so you're not splitting a rack across two lower-capacity PDUs.
• 3-Phase Input: Pulls power across three phases instead of one, which balances load better than single-phase PDUs at this capacity and is the standard approach for high-density data center rows.
• 30A Input Current at IEC 60309 Connector: Matches standard data center 3-phase 30A circuits — the IEC 60309 pin-and-sleeve connector is the industry-standard interface for this current class, so it drops into existing whip and receptacle infrastructure without a connector swap.
• 240/415V Input, 240V AC Output: Accepts a 240/415V 3-phase feed and delivers clean 240V AC to each outlet — the voltage most commercial server and network hardware with C14 inlets expects.
• 0U Rackmount Form Factor: Mounts in the vertical rear channel rather than consuming horizontal rack units, so all 42U (or whatever your frame height is) stays available for compute, storage, and networking gear instead of power distribution.
• 10ft Cord Length: Long enough to reach overhead or underfloor 3-phase whips in most cabinet layouts without an extension, reducing the chance of a mid-run splice.
• 50/60 Hz Frequency Support: Works on both 50Hz and 60Hz utility power, which matters if you're standardizing PDU hardware across facilities in different regions rather than stocking region-specific SKUs.

Integration & Compatibility

C1X24VT-5PPA17AC (often searched as C1X24VT 5PPA17AC) is built to drop into standard rack frames that support 0U vertical PDU mounting in the rear channel — check your cabinet's PDU mounting brackets or channel spacing before ordering, since 0U PDUs are frame-dependent for physical fit. Downstream equipment needs a standard IEC C14 power inlet to mate with the unit's 24 C13 outlets; this covers the large majority of rack servers, switches, and network appliances but won't fit gear with NEMA or locking-outlet requirements without an adapter cord. On the input side, confirm your rack's PDU whip terminates in IEC 60309 30A 3-phase to match this unit's input connector before installation — mismatched input connectors are the most common ordering error on 3-phase PDUs.

Why 3-Phase 0U Matters for Rack Density

A rack running mixed compute and network gear at high density will often blow past what a single-phase strip can carry before it runs out of outlets. Splitting 17.3kW of capacity across three phases instead of one keeps circuit loading balanced and avoids tripping a single overloaded leg — a common failure mode when facilities try to force high-density racks onto single-phase power distribution units. If you're planning a new row of racks, it's worth reviewing a power and capacity planning guide before finalizing PDU counts per cabinet, since 0U vertical units like this one are usually paired with a second unit on the opposite rail for full A/B redundancy. Server Technology's Server Technology PDU lineup covers switched, monitored, and basic models in this same Switched PRO1 Expansion series, so if you need outlet-level power cycling or remote monitoring on top of straight distribution, look at the switched variants in the same family rather than a basic non-networked strip. Pair this unit with a network equipment cabinet sized for 0U rear-channel PDU mounting, and coordinate cord routing with your rack cable management planning so 24 individual C13 cords don't turn into a troubleshooting headache six months in.

Frequently Asked Questions

Q: How many outlets does the C1X24VT-5PPA17AC have?

A: It has 24 IEC C13 outlets fed from a single 3-phase input.

Q: What's the input connector and current rating on the C1X24VT-5PPA17AC?

A: It uses an IEC 60309 input connector rated for 30A, accepting a 240/415V 3-phase feed.

Q: Does the C1X24VT-5PPA17AC take up rack unit space?

A: No — it's a 0U rackmount unit that installs in the vertical rear channel of the cabinet, so it doesn't consume horizontal U space.

Q: What's the total power capacity of the C1X24VT-5PPA17AC?

A: 17.3kW total capacity across all 24 outlets.

Q: What output voltage does the C1X24VT-5PPA17AC deliver to connected equipment?

A: 240V AC at each of the 24 C13 outlets.

Q: How long is the input cord on the C1X24VT-5PPA17AC?

A: The input cord is 10ft.

Ted Perry

The C1X24VT-5PPA17AC is a straightforward density play: 24 C13 outlets and 17.3kW off one 3-phase 30A feed, in a 0U form factor that doesn't cost you a single rack unit. That's the spec that matters most when you're speccing out a new row — every outlet you can pull off a vertical rear-channel unit is an outlet you don't have to find horizontal rack space for.

Technical Highlights:

• 17.3kW capacity across 24 outlets: works out to roughly 720W average per outlet if evenly loaded, though real-world loading is never perfectly even — plan your circuit breakdown against actual nameplate draw of connected gear, not the average.
• 30A 3-phase input via IEC 60309: this is a standard data center whip connector, so retrofit installs into existing 3-phase circuits should be plug-compatible without an electrician re-terminating the drop.
• 10ft input cord: gives you reach to overhead busway or underfloor whip drops in most cabinet rows without needing a field-run extension, which is one less splice point to fail.

Deployment Considerations:

• This is a basic (non-switched, non-metered) distribution unit based on available specs — if you need remote outlet cycling or per-outlet power monitoring, confirm with the switched or monitored variant in the Switched PRO1 Expansion series before ordering, since this listing doesn't carry network management specs.
• 0U vertical PDUs are frame-dependent — verify your cabinet's rear channel supports 0U mounting brackets before ordering; it won't retrofit into a rack built only for horizontal 1U/2U PDU trays.

This is the right call for a new 42U-class server or network rack row where you're running high-density 1U/2U compute and switching gear and need a single 3-phase feed to cover the whole cabinet without sacrificing usable rack space to a horizontal PDU tray.