Lenovo 90Y3016 C13 to NEMA 5-15P 10A Line Cord

Overview

The Lenovo 90Y3016 is a 2.8-meter (9.19 ft) standard line cord rated at 10A/120V AC, terminated with an IEC 60320 C13 female connector on one end and a NEMA 5-15P male plug on the other. It is the replacement or spare power cable used across a broad range of Lenovo server, storage, and peripheral deployments where a standard North American outlet feed is required. If you are provisioning a rack or replacing a missing cord on a Lenovo system drawing from a standard 120V circuit, the 90Y3016 is the factory-spec cable that fits.

This is not a universal bargain cord — it is a Lenovo-sourced line cord matched to the connector and current ratings Lenovo specifies for its commercial equipment. For data centers and server rooms where traceability and manufacturer-spec compliance matter, that distinction is worth noting.

Key Features

• 2.8 m (9.19 ft) Length: Long enough to reach a PDU or wall outlet from a standard rack-mounted server without extension cords or awkward cable management. In a 42U rack with PDUs mounted mid-rail, this length covers top-of-rack placement cleanly — you are not fighting a 6-ft cord that comes up 8 inches short.
• IEC 60320 C13 Female Connector: The C13 is the standard inlet on virtually every rack server, UPS, KVM, and managed PDU in North American data centers. It seats positively with an audible click and locks against accidental disconnection — relevant in high-vibration environments like warehouse server closets or mobile deployments.
• NEMA 5-15P Male Plug: Mates directly with standard 15-amp 120V wall outlets and PDU receptacles found in most North American facilities. No adapter needed for standard utility power. If your PDUs use C19/C20 or L6-30 connections, this is not the right cord — 5-15P is strictly for standard 120V outlets.
• 10A/120V AC Rating: The 10-amp continuous rating gives comfortable headroom on a 15A branch circuit (NEC 80% rule puts continuous load limit at 12A). For a single Lenovo server drawing 4–7A at typical load, this cord carries it without thermal stress. Do not use it on circuits where the equipment load approaches or exceeds 10A continuous.
• Broad Device Compatibility: Suited for servers, computers, monitors, printers, and general peripherals that use a C13 inlet. Works equally well on non-Lenovo equipment using the IEC 60320 C13 standard — an NVR chassis, a rack-mount UPS auxiliary output, or a KVM switch are all valid use cases if they draw within the 10A/120V rating.
• Manufacturer-Spec Replacement: Sourced to Lenovo's part number 90Y3016, this cord meets the connector and cable specifications Lenovo documents for its commercial product lines. When a data center audit or insurance review requires manufacturer-spec cabling, having the OEM part number on record closes that question without a conversation.

Integration and Compatibility

The 90Y3016 is a passive cable — there is nothing to configure. Compatibility is determined entirely by two factors: the device's inlet type (must be IEC 60320 C13) and the outlet type available (must be NEMA 5-15P or compatible 15A 120V receptacle). Any Lenovo server, storage unit, or peripheral with a C13 inlet that operates on 120V will accept this cord. The same applies to non-Lenovo hardware sharing those connector and voltage standards.

In power supply and infrastructure planning, cable standardization across a rack reduces substitution errors during maintenance. Stocking the correct OEM-spec cord for each platform — rather than a mix of generic replacements — simplifies spare-parts management in environments with service contracts or depot-repair programs.

For deployments involving Lenovo rack servers and tower systems, this cord pairs with standard rack PDUs that provide NEMA 5-15 receptacles. Higher-density deployments drawing more than 10A per server will require a C13-to-L6-20P or C13-to-C20 cord depending on PDU design — the 90Y3016 is strictly for standard 120V/15A utility circuits.

Integrators building out server rooms, branch-office IT closets, or surveillance NVR racks will find the 90Y3016 a useful power cable to stock as a spare. Its 2.8m run covers the majority of rack-to-PDU distances without requiring a longer cord that adds cable management bulk.

Frequently Asked Questions

Q: What connectors does the Lenovo 90Y3016 use?

A: The 90Y3016 has an IEC 60320 C13 female connector on the device end and a NEMA 5-15P male plug on the wall/PDU end. It is designed for standard North American 120V outlets.

Q: What is the current and voltage rating of the 90Y3016?

A: The cord is rated at 10 amps continuous at 120V AC. It is suitable for equipment drawing up to 10A on a standard 120V branch circuit.

Q: How long is the 90Y3016 power cord?

A: The cord is 2.8 meters, which is approximately 9.19 feet — long enough to connect a rack-mounted server to a mid-rail or bottom-of-rack PDU in a standard 42U cabinet.

Q: Will the 90Y3016 work with non-Lenovo servers or devices?

A: Yes. Any device with an IEC 60320 C13 inlet operating on 120V AC at or below 10A is compatible. The connector standard is widely used across servers, UPS units, KVM switches, NVRs, and monitors regardless of manufacturer.

Q: Is the 90Y3016 suitable for use with a UPS or rack PDU?

A: Yes, provided the PDU or UPS offers NEMA 5-15 receptacles and the circuit is 120V. This cord is not appropriate for PDUs with C19, L6-20, or L6-30 receptacles, or for 208/240V circuits.

Jerry Tildsen

The Lenovo 90Y3016 is exactly the kind of component that gets overlooked during a rack build and then causes a last-minute scramble at commissioning. It is a 2.8-meter, 10A/120V C13-to-NEMA-5-15P line cord — not exciting, but the right spec matters. The 9.19-foot run is the length Lenovo engineered for its server and storage product lines operating on North American utility power, and stocking it means you are not improvising with a mismatched generic at go-live.

Technical Highlights:

• 10A/120V Rating: At 10 amps continuous, this cord operates safely on a standard 15A branch circuit under the NEC 80% continuous load rule (12A ceiling). A single Lenovo server at typical datacenter load runs well within that envelope — you are not pushing the cord's thermal limits under normal conditions.
• IEC 60320 C13 Connector: The C13 inlet is the near-universal standard for rack-mounted commercial equipment. This cord fits Lenovo servers, storage enclosures, KVM units, and NVRs with a C13 inlet without any adapter — the connector seats positively and stays put.
• 2.8 m Cable Run: The 9.19-foot length accommodates top-of-rack and mid-rack server placement to a PDU mounted at the rear vertical rail without excess slack. A 6-foot cord often falls short; a 15-foot cord creates cable management overhead. This length is the practical middle ground for a standard 42U cabinet.

Deployment Considerations:

• Verify your PDU receptacle type before ordering. The NEMA 5-15P plug on the 90Y3016 fits standard 120V/15A outlets only. If your PDU uses C19, L6-20, or L6-30 receptacles — common in higher-density or 208V environments — you need a different cord entirely.
• This cord is rated for 120V AC. Do not use it in 208V or 240V circuits even with a compatible outlet adapter — the voltage rating is a hard limit, not a guideline.

The 90Y3016 is the right stock item for Lenovo-heavy branch-office IT closets and surveillance NVR racks running on standard 120V utility power, where maintaining OEM-spec cabling simplifies both service documentation and spare-parts audits.