Ubiquiti U-CABLE-PATCH-3M-RJ45-BL Cat6 Patch Cable
Overview
The Ubiquiti U-CABLE-PATCH-3M-RJ45-BL is a 3-meter pre-terminated Cat6 patch cable engineered for Ubiquiti UniFi infrastructure deployments. The cable ships ready to deploy — no field termination required — which eliminates installation labor and reduces the risk of mismatched impedance or poor connections that plague hand-crimped runs. At 3 meters (approximately 10 feet), this length bridges typical cabinet-to-access-point, cabinet-to-gateway, and switch-to-edge-device spacing in office, warehouse, and small-to-medium industrial network environments.
The blue outer jacket provides visual identification across mixed cabling runs, making device tracking and future troubleshooting simpler. RJ45 connectors at both ends are standard pinout for Ethernet, so this cable integrates with any UniFi switching, access point, or gateway device in your lineup.
Key Features
- Cat6 Rated: Supports up to 10 Gbps data rates over shorter distances — sufficient for UniFi PoE access points, multi-port switches, and 1 Gbps uplinks without bottlenecking. You won't overshoot your needs in typical enterprise LAN deployments, and the extra headroom means future hardware upgrades won't require cable replacement.
- Pre-Terminated RJ45 Connectors: Both ends are factory-crimped and tested, eliminating field termination labor and the defect rates associated with manual crimping. Deploy out of the box — no crimper, punch-down tool, or tester required at install time.
- 3-Meter Length: Fits standard cabinet-to-wall or cabinet-to-device runs without excess slack or the cost/complexity of custom lengths. If you need longer runs (wall-to-distant AP or gateway), plan for additional cable or conduit; shorter lengths are available in the Ubiquiti catalog if your spacing is tighter.
- Blue Jacket: Color-coded for easy identification and logical tracking in mixed-media installations. Useful for visual continuity when documenting network diagrams on-site or managing MAC address assignments post-deployment.
- Copper Construction: Full copper conductors (not CCA — copper-clad aluminum) ensure signal integrity and reduced attenuation over the full 3-meter run. Important in high-density PoE deployments where voltage drop on longer runs can impact power delivery to low-power devices.
- UniFi Compatibility: Tested and compatible with all current Ubiquiti patch cables and switching infrastructure. Works with UniFi Dream Machine, UniFi switches (USW-Pro, USW-Lite, USW-Industrial), and all PoE-powered access points and gateways in the UniFi line.
Integration & Compatibility
The U-CABLE-PATCH-3M-RJ45-BL integrates directly into any Ethernet-based network segment. Pair it with PoE power supplies and UniFi managed switches to create redundant, monitored network backhauls for access points and edge security cameras. The cable meets standard Ethernet pinout specifications (568B), so it also works with non-Ubiquiti devices, though field testing with legacy equipment is recommended if mixing vendors.
What's in the Box
- 1x Ubiquiti U-CABLE-PATCH-3M-RJ45-BL Cat6 Patch Cable (3m, Blue)
When to Choose a Different Model
If your cabinet-to-device distance exceeds 3 meters, source a longer variant from the Ubiquiti catalog — Cat6 is available in 5m, 10m, and custom lengths. If you require outdoor-rated or UV-hardened jackets for aerial or exposed runs, consult Ubiquiti's industrial-grade cable line. For in-wall plenum installations requiring fire-rating compliance, verify local building codes; standard Cat6 may require conduit in some jurisdictions.
Frequently Asked Questions
Q: Is the U-CABLE-PATCH-3M-RJ45-BL suitable for PoE power delivery?
A: Yes. Cat6 copper conductors carry PoE current without issue. The cable will support standard 802.3af (15.4W), 802.3at PoE+ (30W), and 802.3bt PoE++ (up to 90W) — limited only by your power injector or PoE switch port rating, not by the cable itself.
Q: Can I use the U-CABLE-PATCH-3M-RJ45-BL with non-Ubiquiti network equipment?
A: Yes. The cable follows standard Ethernet pinout (568B) and RJ45 specification, so it works with any standard Ethernet-compatible device — switches, routers, cameras, and endpoints from any vendor.
Q: What is the data rate ceiling on this cable?
A: Cat6 supports up to 10 Gbps over distances up to 55 meters, though real-world performance at 10 Gbps is typically limited to 180 feet or less depending on signal quality. For most UniFi access point and switch backhauls, the cable operates comfortably well below that ceiling.
Q: Is the cable shielded or unshielded?
A: The evidence provided does not specify shielding type. Contact the manufacturer or your distributor to confirm shielded vs. unshielded construction if EMI mitigation is required in your environment.
Q: How do I identify cable direction if I need to reverse it?
A: Ethernet is bidirectional — orientation does not matter. Either end can plug into any standard RJ45 socket without performance penalty.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The U-CABLE-PATCH-3M-RJ45-BL is a straightforward accessory, but it matters more than you might think. At 3 meters, this Cat6 cable solves a real problem in UniFi deployments: the gap between cabinet and edge device. Pre-terminated means zero field-crimping risk — a non-trivial win if you're rolling out dozens of APs or switches across multiple sites.
Technical Highlights:
- Cat6 Rated for 10 Gbps: Overkill for most single-AP runs, but valuable insurance if you ever stack multiple devices on one switch port or plan uplink redundancy later. No retrenchment needed.
- Copper Conductors: Full copper (not CCA) means lower attenuation and better PoE delivery under load. Matters when you're power-stacking multiple PoE devices and voltage drop creeps into the equation.
- 3-Meter Length: Fits the typical 8–10 foot cabinet-to-wall or cabinet-to-ceiling-mount scenario without forcing you to coil excess slack or run conduit. Shorter or longer variants are available if your topology diverges.
Deployment Considerations:
- Verify that your switch port supports the power budget of all downstream devices. Cat6 itself won't limit PoE delivery, but an underpowered switch will.
- If your environment requires shielding for EMI suppression (industrial floors, RF-dense spaces), confirm the shielding specification with the manufacturer — the evidence provided does not clarify shielded vs. unshielded construction.
Best suited for planned UniFi rollouts where you can bulk-purchase exact lengths and reduce labor at deployment time. If you're retrofitting existing infrastructure with mismatched cable runs, this is a good standardization point for future segments.
