Camden CX-92S-06TDS 600 lbs Surface Mount Magnetic Lock
The Camden CX-92S-06TDS is a surface-mount magnetic lock engineered for double-door access control deployments requiring high holding force and networked integration. Rated for 600 lbs electromagnetic holding capacity on 24VDC, this lock eliminates mechanical strike installation overhead while maintaining full TCP/IP command and real-time status feedback. Integrators favor this model for retrofits into existing aluminum and steel frame doorways where frame modification is not feasible and centralized access policy enforcement is a requirement.
Key Features
- 600 lbs Holding Force: Electromagnetic capacity sufficient for double-door and high-traffic commercial entryways. Eliminates mechanical strike binding and maintenance cycles.
- Surface Mount Design: No frame modification required—reduces installation labor and permits rapid retrofit into existing door assemblies without structural changes.
- 24VDC Operation: Compatible with standard access control power supplies and UPS battery backup systems. Low voltage eliminates high-voltage licensing and hazard labeling requirements.
- TCP/IP Integration: Networked lock status, real-time audit logging, and remote unlock commands via centralized access control platform. Supports credential validation at the controller, not the lock.
- Adjustable Timer Control: Configurable dwell time and door-open detection delay enable time-controlled access scenarios and integration with request-to-exit hardware.
- Aluminum & Steel Compatibility: Fits standard frame profiles without adapter plates or custom fabrication.
The CX-92S-06TDS bridges mechanical-lock simplicity with network-based access policy. Because the lock is electromagnetic rather than motorized, there are no moving parts to jam or wear—power-off defaults to locked state, providing fail-secure behavior without additional mechanics. This passive design also means lower inrush current and reduced demand on battery backup during extended outages.
TCP/IP communication is the operational win here. Rather than manage access at individual locks, integrators deploy this lock as a networked endpoint. An access control platform (such as a standalone controller or hosted cloud service) validates credentials, logs every unlock event, and can remotely command the lock to release or hold based on time-of-day schedules, personnel status, or emergency lockdown triggers. Real-time feedback tells you whether the door is actually held closed—missing information with purely mechanical strikes.
Surface mounting also simplifies troubleshooting. If the lock fails in the field, swap it in 15 minutes without drywall cutting or frame reinforcement. Aluminum-frame doors, which are common in institutional and commercial retrofits, often cannot accommodate recessed strikes; the CX-92S-06TDS avoids that friction entirely.
The lock carries manufacturer warranty coverage and is sourced new from factory channels. Standard 24VDC integration keeps bill-of-materials costs predictable—no exotic power supplies or control cards. Pair this with an ONVIF-compatible access control platform or a dedicated NVR with relay outputs, and you have a complete networked door security layer that scales from single-door installations to multi-building campuses.
Jerry TildsenPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
We've installed the CX-92S-06TDS across retail, healthcare, and education campuses, and it consistently outperforms mechanical strikes in mixed-frame environments. The 600 lbs holding force is genuine—we've tested it under load, and it holds without creep or chatter. What separates this lock from budget alternatives is the TCP/IP feedback loop: you know in real time whether a door is held, released, or physically forced open. That audit trail is non-negotiable in healthcare and finance. The surface-mount envelope also means no callbacks for frame reinforcement or custom striker plates. In a 20-door retrofit we completed last year, the CX-92S-06TDS saved two weeks of installation time versus recessed-strike alternatives because aluminum frames didn't need modification.
Technical Highlights:
- 24VDC Fail-Secure Design: Power loss or control signal failure leaves the lock in the locked state. No spring-return mechanism needed—electromagnetic holding is passive until the controller sends release. Reduces parts count and inrush current on battery backup systems.
- TCP/IP Real-Time Status: Lock status (held, released, forced-open) is reported to the access control platform in real time. Enables conditional logic: if a door remains open beyond N seconds, trigger an alert or send a push notification to security staff.
- 600 lbs Holding Force: Tested holding capacity; verified under load testing. Eliminates mechanical strike binding on high-traffic or mis-aligned double-door pairs. Single electromagnetic element—no solenoid striker or mechanical latch to maintain.
- Surface Mount—No Frame Surgery: Fits aluminum-frame storefront doors, steel frames, and hollow-metal doors without structural modification. Critical advantage in retrofit work where frame cutting is prohibited or cost-prohibitive.
- Adjustable Dwell & Door-Hold Timer: Configurable unlock-to-relock timing allows integration with manual request-to-exit buttons, motion sensors, or credential readers. Supports both momentary and time-release unlock modes.
Deployment Considerations:
- Network Dependency: Lock release is contingent on TCP/IP communication. If the access control platform or network segment is unavailable, the lock remains held. Plan for local override (manual key or emergency release button) and UPS power for the controller.
- Door Alignment Critical: 600 lbs holding force assumes proper door-to-frame alignment. Warped or sagging doors may not seat flush; test the door swing before lock installation to avoid operational nuisance calls.
- Power Supply Sizing: 24VDC supply must be sized for inrush current during release and any auxiliary hardware (request-to-exit sensor, door position switch). Confirm amperage rating with access control platform spec sheet.
- Frame Material Compatibility: Confirm surface-mounting footprint against your frame profile (aluminum extrusion, steel tube, hollow-metal door). Most common commercial frames are compatible; custom frame geometry may require adapter plate (not included).
- Manual Override Access: Install manual release key or emergency unlock button in an accessible location (e.g., inside the secure area or at a staffed station). Test quarterly to ensure it functions independently of the network.
The CX-92S-06TDS is the right choice for integrators deploying networked multi-door access control in retrofit environments where frame modification is off the table. Its 600 lbs capacity and TCP/IP feedback eliminate the operational blind spots of mechanical strikes, and surface mounting cuts installation complexity. If your project requires fail-secure behavior, audit logging, and zero frame engineering, this lock earns its place in the specification. See the full Camden catalog for complementary hardware and controllers.
