Altronix T2SPK7F8SPDQ 8-Door SiPass Access Control Power Integration Wall Mount Kit

Overview

The Altronix T2SPK7F8SPDQ is a purpose-built power integration kit engineered specifically for Altronix/Siemens SiPass access control deployments covering up to eight doors. Rather than patching together a generic power supply with a separate panel, this kit delivers 24VDC at 10A from a 115V input — enough headroom to drive eight lock outputs simultaneously without hunting for supplemental power. If you're commissioning a mid-size commercial building, a campus facility, or a multi-floor office block on SiPass, the T2SPK7F8SPDQ eliminates the power design step and ships the hardware pre-matched to the platform.

Key Features

• 24VDC @ 10A Power Supply (115V Input): Ten amps at 24 volts covers eight mag-lock or electric-strike circuits with margin to spare. You won't be recalculating load budgets for each door — the supply is sized to the panel's rated output count from the factory.
• 8 Fail-Safe Outputs (12/24VDC): Eight independently switched fail-safe outputs let magnetic locks release on loss of power, which is the code-required behavior on egress paths in most AHJ jurisdictions. The dual-voltage flexibility (12 or 24VDC per output) means you're not locked into a single lock hardware family.
• 8 Fail-Secure Outputs (12/24VDC): Eight fail-secure outputs hold electric strikes and fail-secure locks energized on power loss — correct for server rooms, pharmaceutical storage, or any space where an open-on-failure door is a security liability. Same dual-voltage selectability as the fail-safe bank.
• 8 Managed Auxiliary Outputs with PTC Protection: Eight PTC-protected auxiliary outputs at 12/24VDC support request-to-exit devices, door position switches, and auxiliary readers without external fusing. PTC resettable protection means a wiring fault or shorted device won't take down adjacent outputs — the affected circuit self-recovers once the fault clears.
• 12VDC Voltage Regulator: An onboard 12VDC regulator provides a stable low-voltage rail for readers and other 12V peripherals. Running readers off the same enclosure as the lock power — on a regulated output — removes the ground-loop and voltage-droop issues that plague long reader cable runs on unregulated supplies.
• Wall Mount Kit Enclosure: The kit ships as a complete wall-mount assembly. For Siemens SiPass integrations, enclosure-level integration matters: this hardware is matched to the SiPass platform rather than adapted from a generic power chassis, which reduces commissioning time and simplifies the submittal package.
• Cam Lock, Tamper Switch, and Battery Leads Included: The cam lock secures the enclosure against casual intrusion. The tamper switch reports unauthorized enclosure access to the access control panel — a mandatory feature on UL-listed access control installations. Battery leads are pre-wired for backup battery connection, supporting power-fail continuity without additional wiring.

Integration & Compatibility

The T2SPK7F8SPDQ is specifically identified as an Altronix integration kit for Siemens SiPass access control systems. The hardware architecture — dual fail-safe/fail-secure output banks, managed aux outputs with PTC, and regulated 12VDC reader rail — maps directly to the SiPass panel's door module wiring requirements. This is not a universal access control power supply adapted for SiPass; it is a co-engineered kit for that platform. Installers deploying access control on SiPass should confirm door count and lock type before ordering: if your project exceeds eight doors per enclosure, additional T2SPK7F8SPDQ units can be deployed per riser or per floor. For projects requiring PoE-based reader infrastructure, pair this kit with a PoE switch for IP reader power distribution. Consult the access control power supplies category for alternative Altronix enclosures if your door count, lock type mix, or panel platform differs.

What's in the Box

• 1x T2SPK7F8SPDQ wall mount enclosure with integrated power supply and output modules
• 1x Cam lock
• 1x Tamper switch
• 1x Set of battery leads
• 1x Set of wire ties
• 1x Set of mounting hardware

Frequently Asked Questions

Q: How many doors does the T2SPK7F8SPDQ support?

A: The T2SPK7F8SPDQ supports up to 8 doors. It provides 8 fail-safe outputs, 8 fail-secure outputs, and 8 managed auxiliary outputs — one complete set of door control circuits per door position.

Q: Can I use the T2SPK7F8SPDQ with access control platforms other than Siemens SiPass?

A: This kit is engineered specifically as an Altronix/Siemens SiPass integration. While the power supply and output modules are electrically compatible with standard 12/24VDC lock hardware, the kit is designed and matched for SiPass panel wiring. Using it with a different panel platform is outside its defined integration scope — verify compatibility with the target panel manufacturer before substituting.

Q: What is the output voltage and current rating of the T2SPK7F8SPDQ power supply?

A: The integrated power supply delivers 24VDC at 10A from a 115V AC input. The fail-safe, fail-secure, and auxiliary outputs are selectable at 12 or 24VDC per output.

Q: Does the T2SPK7F8SPDQ include tamper protection?

A: Yes. A tamper switch is included and reports unauthorized enclosure access to the access control panel. A cam lock is also included to physically secure the enclosure door.

Q: Does the kit include backup battery support?

A: Yes. Battery leads are included in the kit, allowing connection of a backup battery for power-fail continuity. The enclosure is designed to accommodate battery backup as part of the SiPass integration.

Q: What protection do the auxiliary outputs provide?

A: The 8 managed auxiliary outputs include PTC (positive temperature coefficient) resettable overcurrent protection. A faulted or shorted device on one aux output will not take down adjacent outputs, and the affected circuit self-resets once the fault is cleared — no fuse replacement required.