IP Camera Accessories | Mounts, Enclosures, Lenses, IR & Power

Deployment Considerations

Environmental protection and weather resistance
Mounting stability and load support
Power and voltage compatibility
Cable management and termination quality
Compliance with local safety standards

Sub categories

Showing Results for Accessories

Compare

Out of stock
Valcom

SKU: V-WGVL550-2

Valcom V-WGVL550-2 Wire Guard for VL550

Wire guard for VL550 speakers in ceiling and rack mounts
- Corrosion-resistant wire construction shields speaker assembly from contact
- Fits ceiling-suspended or rack-mount installations without custom hardware
- Accommodates microphone connections for integrated two-way audio systems
Special Order · Ships in 2-3 weeks

$117.99 $105.99 Save $12.00

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: V-WMCA

Valcom V-WMCA Wireless Master Clock Transceiver

Wireless master clock transceiver with browser-based setup
- Wall-mounted time source synchronizes distributed clock networks
- Browser interface eliminates software installation and remote management
- Microphone input integrates paging announcements with time sync
Special Order · Ships in 2-3 weeks

$2,573.99 $2,307.99 Save $266.00

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: V-WMCRA

Valcom V-WMCRA Wireless Master Clock Repeater

Wireless clock repeater extends signal range across multi-zone facilities
- Wall-mounted repeater retransmits correction signals to distributed clocks
- Integrated microphone support for audio coordination in clock networks
- Expands Valcom wireless clock coverage without additional hardwired infrastructure
Special Order · Ships in 2-3 weeks

$1,085.99 $973.99 Save $112.00

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-A24

Valcom VB-A24 Angled Backbox for Ceiling Mount

Angled ceiling backbox for Valcom clocks and speakers
- Pre-fabricated design eliminates custom bracket fabrication and labor
- Angled geometry optimizes device positioning for visibility and sound
- Mounts overhead to support commercial audio and visual installations
Special Order · Ships in 2-3 weeks

$77.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Valcom

SKU: VB-R12

Valcom VB-R12 Recessed Backbox Mount

Recessed backbox mount for square faceplates on walls and ceilings
- Flush-mount design eliminates visible brackets for clean drywall integration
- Dual orientation supports both wall and ceiling installations with one SKU
- White powder-coated finish blends seamlessly into standard indoor spaces
In stock · Ships same business day

$75.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-R17-D

Valcom VB-R17-D Recessed Mount Backbox

Recessed backbox for VIP-9880 IP speakers with deep square FlexHorn mount
- Recessed design fits standard wall cavities and ceiling mounts for flush finish
- Deep square FlexHorn faceplate compatibility with proper depth alignment
- Engineered for Valcom VIP-9880 IP speaker system integration
Special Order · Ships in 2-3 weeks

$85.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-R19

Valcom VB-R19 Recessed Backbox Mount

Recessed backbox mount for Valcom large clocks and speakers
- Flush wall mounting fits standard cavities for clean, integrated installation
- White finish with light texture powder coat suits indoor facilities
- Compatible with Valcom large clock and speaker systems
Special Order · Ships in 2-3 weeks

$81.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-R22

Valcom VB-R22 Recessed Mount Backbox

Recessed backbox for Valcom VIP-419 and VIP-429 clock/speaker combos
- Fits standard wall cavities with typical stud spacing for clean, flush installation
- Drywall-compatible construction integrates seamlessly into commercial interior walls
- Quick-access design supports easy maintenance and component service after install
Special Order · Ships in 2-3 weeks

$79.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-S11

Valcom VB-S11 Surface Mount Backbox

Surface-mount backbox for Valcom VIP-418 speaker systems
- Column mount design reduces installation labor in indoor spaces
- White powder-coated texture finish for standard commercial environments
- Square faceplate compatibility with Valcom speaker assemblies
Special Order · Ships in 2-3 weeks

$75.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-S20

Valcom VB-S20 Surface Mount Backbox

Surface-mount backbox for Valcom clock and speaker systems
- No recessing required—installs directly to wall with column mount design
- White powder-coated steel finish suits office, retail, industrial, institutional
- Integrates with Valcom clock and speaker product lines for cable management
Special Order · Ships in 2-3 weeks

$81.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VB-S23

Valcom VB-S23 Surface Mount Backbox

Surface mount backbox for Valcom clock and speaker ceiling install
- Fits VIP-419 and VIP-429 systems without cavity prep on finished ceilings
- Mounts directly to hard surfaces for quick professional ceiling installation
- Compact enclosure design supports clock and speaker assemblies in one unit
Special Order · Ships in 2-3 weeks

$77.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VC40R-4

Valcom VC40R-4 4 Position Backplane Cable

40-pin ribbon cable for 4-position Valcom ACS intercom expansion
- Connects feature cards in rack-mounted Valcom ACS expandable systems
- 4-position backplane configuration for modular card installations
- 40-pin ribbon connector design for standard rack environments
Special Order · Ships in 2-3 weeks

$159.99

Add to Cart
The item has been added
Compare

Out of stock
Valcom

SKU: VC40R-9T

Valcom VC40R-9T 9 Position Backplane Cable

40-pin ribbon cable with 16 connectors for Valcom ACS intercom expansion
- 9-position backplane cable supports feature card expansion in ACS systems
- Integrated terminator and 16 connectors for rack-mounted installations
- Microphone input compatible for multi-zone audio configurations
Special Order · Ships in 2-3 weeks

$275.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Valcom

SKU: VMT-1

Valcom VMT-1 600-Ohm Impedance Matching Transformer

600-ohm passive transformer for telephone and PA system audio matching
- Dual-mode operation handles both input and output matching in one unit
- Balanced and unbalanced audio support with zero power required
- Eliminates signal reflections and insertion loss across legacy infrastructure
In stock · Ships same business day

$46.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Valcom

SKU: VMT-2

Valcom VMT-2 600 Ohm Audio Isolation Transformer

Passive 600 Ohm transformer eliminates ground loop hum in distributed audio
- Galvanic isolation via magnetic coupling—no external power required
- 600 Ohm line-level impedance for mixers, amplifiers, and audio processors
- Wall-mount design weighs 0.5 lbs for retrofit into existing systems
In stock · Ships same business day

$37.99 $33.99 Save $4.00

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Valcom

SKU: VP-12124

Valcom VP-12124 24VDC 12A Switching Power Supply

24VDC/12A switching supply for multi-device audio and comms systems
- 300W output powers up to a dozen endpoints simultaneously without voltage sag
- Accepts 120V or 240V AC input, 47–63 Hz for flexible facility installation
- Wall-mounted switching topology runs efficient and cool in equipment rooms
In stock · Ships same business day

$525.99 $470.99 Save $55.00

Add to Cart
The item has been added

What to Look For When Buying

The six decisions that matter most before you spec.

Match Bracket to Camera + Surface

A dome camera mounted on a textured wall needs a wall-mount adapter with a gasket; mounted on a pole it needs a pole-mount arm; mounted on an eave it may need a pendant. Third-party brackets exist but brand-specific brackets include proper camera cable routing and weather gasketing. Buying a $40 generic bracket to save on a $80 Axis bracket usually costs more in installation time.

Enclosure NEMA Rating

NEMA 3R = light rain; NEMA 4 = splash + driving rain; NEMA 4X = above + corrosion resistance (coastal, industrial); NEMA 6 = temporary submersion. For weather-exposed camera enclosures, NEMA 4X is the commercial standard. For mission-critical outdoor gear, pair NEMA 4X enclosure + IP67 camera + IK10 vandal rating.

C/CS-Mount Lens Selection

Box cameras use interchangeable C-mount (17.526mm flange) or CS-mount (12.5mm flange). Lens focal length + sensor size determines field of view: a 4mm lens on a 1/3" sensor gives ~60° horizontal FOV. Our DORI guide covers lens selection by scene distance. F-stop matters for low-light; P-iris for auto-exposure.

IR Illuminator Wavelength

850nm IR is more efficient but produces a faint visible red glow (deterrent or accidental giveaway, depending on use case). 940nm is truly covert but requires ~2x the power for the same effective range, and many cameras have lower sensitivity at 940nm. Match illuminator wavelength to camera IR-cut filter spec, or image washout results.

Power Supply Sizing & Distance

12VDC cameras at 100ft from a power supply drop significant voltage over 18-gauge wire — a camera rated for 12V may see 10.5V at the camera end under load, triggering brownout resets. For long runs, use a higher-voltage power supply (24VAC or 48VDC) and step down at the camera. UL-listed surveillance power supplies (Altronix) publish voltage-drop tables.

Cable Jacket Rating

Indoor Cat6 is rated CM (communications); plenum-rated CMP is required for above-drop-ceiling runs per NFPA 70. Outdoor/direct-burial Ethernet is a different product (CMX, direct-burial gel-filled). Mixing jacket ratings causes code violations and fire inspector rejections. Always spec by run environment, not lowest-cost SKU.

Technology Stack

The specs and acronyms that actually affect outdoor performance.

NEMA vs IP Rating Systems

NEMA is the US enclosure standard (NEMA 1-13); IP is the international standard (IP00-IP68). Rough crosswalk: NEMA 4 ≈ IP66, NEMA 4X ≈ IP66 + corrosion, NEMA 6 ≈ IP67. Some spec sheets list both; when only one is given, the crosswalk is approximate. For coastal, industrial, and food-processing environments, specify NEMA 4X or IP66 + stainless steel.

C-Mount vs CS-Mount Lenses

C-mount: 17.526mm flange focal distance. CS-mount: 12.5mm flange. CS cameras accept both lens types (C lenses need a 5mm adapter ring); C cameras accept only C lenses. Most modern box cameras are CS-mount for lens flexibility. Lens thread is 1-inch × 32 TPI on both.

F-Stop / Iris

F-stop = focal length ÷ aperture diameter. Lower F-stop (wider aperture) means more light, better low-light performance, shallower depth of field. F1.4 is very low-light capable; F1.8 is common commercial spec. P-iris (precise iris) lenses auto-adjust aperture based on scene lighting — reduces over-exposure during day, improves low-light at night.

850nm vs 940nm IR

IR illuminators at 850nm are more energy-efficient and the sensitivity of most camera IR-cut filters peaks here — but 850nm produces a faint visible red glow from the LEDs. 940nm is invisible to human eye but requires ~2x the power or shorter effective range. Many covert-deployment cameras are re-tuned for 940nm sensitivity.

UL-Listed Power Supplies

Underwriters Laboratories listed power supplies meet safety standards for overcurrent, overvoltage, and enclosure isolation. UL 294 specifies additional requirements for access control; UL 603 for security burglary; UL 1310 for Class 2 power. Insurance and code requirements increasingly specify UL-listed supplies — particularly in commercial and institutional installations.

Plenum vs Riser vs PVC Cable

Plenum-rated (CMP) cable uses low-smoke FEP jacket for use above suspended ceilings where smoke spreads through return-air plenums. Riser (CMR) is for vertical shaft runs between floors. PVC (CM) is for open office runs only. Using CM in plenum spaces violates NFPA 70 — costly inspector rejection if caught.

Typical Deployment Scenarios

New Construction Retrofit

Cat6A plenum cable pulled to camera locations with proper service loops, 2-gang electrical boxes at each dome location with weatherproof backbox, Cat6A patch panel at the IDF, UL-listed power supplies for any 12V/24V camera, labeled and tested before cameras are mounted.

Coastal / Corrosive Environment

NEMA 4X stainless-steel enclosures for outdoor cameras, 316-grade stainless brackets, silicone dielectric grease on every connector, hot-dipped galvanized or powder-coated steel poles. Budget 15-25% more on accessories vs. standard outdoor — and plan for 3-5 year inspection cycles rather than 10.

Box-Camera LPR Application

Box camera with 50-150mm telephoto lens, dedicated 850nm IR illuminator at same height as camera, pole-mount bracket with junction box, UL power supply for camera + illuminator. LPR-specific enclosures with anti-reflective glass to avoid nighttime IR bloom. Typical deployment: dedicated lane camera, not general-purpose surveillance.

Parking Garage Retrofit

Existing analog coax cable replaced via NVT Phybridge or similar PoE-over-coax, vandal-resistant dome enclosures at ground level, low-profile bullet cameras on ceiling, LED-plus-IR-compatible illuminators to handle harsh fluorescent lighting. Enclosures rated for vehicle-exhaust environment.

Frequently Asked Questions

Do I need the OEM bracket for my camera, or will a generic bracket work?

For most commercial installations, specify the OEM bracket. Brand-specific brackets include proper cable routing, gasketed weather seals, and mounting-hole patterns matched to the camera — which matters more than the cost savings of a generic bracket. Generic brackets are acceptable for indoor standard-dome cameras on flat surfaces; for outdoor, vandal-rated, or pendant applications, use OEM.

What NEMA rating do I need for outdoor camera enclosures?

NEMA 4 for most weather-exposed deployments (driving rain, snow). NEMA 4X for coastal, industrial, or food-processing environments (adds corrosion resistance — typically stainless steel or fiberglass construction). NEMA 6 for temporary submersion or flood-prone areas. The IP-rating equivalent is IP66 for NEMA 4, IP66 + corrosion for NEMA 4X, IP67 for NEMA 6.

How do I choose the right lens focal length for a box camera?

Work backward from the scene. Identify the farthest point you need identification-grade coverage, use our DORI guide to calculate required pixels-per-foot at that distance, and match lens focal length + sensor size to deliver that PPF. A 4mm lens on a 1/3" sensor covers ~60° horizontal FOV; a 12mm lens on the same sensor covers ~20°. Wide FOV = shorter identification distance.

What's the difference between 850nm and 940nm IR illuminators?

850nm is more energy-efficient — you get more effective range per watt — but produces a faint visible red glow from the LEDs. 940nm is truly invisible to the human eye but requires about 2x the power for equivalent range, and many cameras have lower sensor sensitivity at 940nm. For deterrent visibility or cost-efficient long-range, 850nm; for covert applications, 940nm.

Can I power an IP camera with a generic 12V wall-wart?

Not for a commercial deployment. Generic wall-warts are unregulated, not UL-listed for security applications, and typically don't include surge protection. Use a UL-listed surveillance power supply (Altronix AL series, UL 294 or UL 603) with battery backup where required. PoE is preferred when possible — single cable, centralized power management, UPS-backed.

What cable jacket rating do I need for in-ceiling runs?

Plenum-rated (CMP) cable is required for any run through a return-air plenum space above suspended ceilings (most commercial buildings). Riser (CMR) for vertical shafts between floors. PVC (CM) for open office spaces only. Using non-plenum cable in a plenum space is a fire-code violation under NFPA 70 and will be rejected by inspectors. Budget plenum cable for any building where you're not 100% sure of the return-air path.

Accessories

Deployment Considerations

Sub categories

Showing Results for Accessories

Valcom V-WGVL550-2 Wire Guard for VL550

Valcom V-WMCA Wireless Master Clock Transceiver

Valcom V-WMCRA Wireless Master Clock Repeater

Valcom VB-A24 Angled Backbox for Ceiling Mount

Valcom VB-R12 Recessed Backbox Mount

Valcom VB-R17-D Recessed Mount Backbox

Valcom VB-R19 Recessed Backbox Mount

Valcom VB-R22 Recessed Mount Backbox

Valcom VB-S11 Surface Mount Backbox

Valcom VB-S20 Surface Mount Backbox

Valcom VB-S23 Surface Mount Backbox

Valcom VC40R-4 4 Position Backplane Cable

Valcom VC40R-9T 9 Position Backplane Cable

Valcom VMT-1 600-Ohm Impedance Matching Transformer

Valcom VMT-2 600 Ohm Audio Isolation Transformer

Valcom VP-12124 24VDC 12A Switching Power Supply

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Outdoor Deployments

Frequently Asked Questions

Related Categories

Engineering Reading

Certified Experts

Manufacturer Authorized

Expert Access

Since 2014

Brands

Categories

IP Cameras

Ordering

Legal

Company

Sales & Expert Advice

Customer Service