STI

SKU: BPA1008

STI BPA1008 EnviroArmour Aluminum Back Panel 10x8

• Aluminum construction resists corrosion from salt air, UV, and temperature swings outdoors.
• Rigid mounting substrate supports credential readers, keypads, and biometric sensors at 9VDC.
• Rated for outdoor environments including parking garages, loading docks, and exterior walls.

STI

SKU: BPA1010

STI BPA1010 EnviroArmour Aluminum Back Panel 10x10

• EnviroArmour aluminum construction handles outdoor exposure including salt spray and UV.
• Operates at 9VDC, integrating cleanly into standard low-voltage access control architectures.
• 10×10 in. form factor fits most credential readers; four corner holes accept standard fasteners.

STI

SKU: BPA1412

STI BPA1412 EnviroArmour® Aluminum Back Panel 14x12

• 14×12 in. aluminum surface mounts readers, keypads, and strikes to any door frame.
• Outdoor-rated EnviroArmour® construction resists UV, salt spray, and physical impact.
• Pre-drilled holes and 7mm masonry compatibility simplify concrete and brick installs.

STI

SKU: BPA1614

STI BPA1614 EnviroArmour Aluminum Back Panel 16x14

• Aluminum construction resists corrosion in salt-air, coastal, and high-moisture environments.
• 16" × 14" panel provides ample mounting surface for reader heads and strike assemblies.
• 9VDC operation integrates directly with compatible STI EnviroArmour reader and strike systems.

STI

SKU: BPA1816

STI BPA1816 EnviroArmour Aluminum Back Panel 18x16

• Aluminum construction resists corrosion, salt spray, and UV in outdoor deployments.
• 18×16 in. footprint accommodates multi-reader and strike assemblies on a single panel.
• 9VDC power distribution supports battery-backed and hardwired access control circuits.

STI

SKU: BPA2016

STI BPA2016 EnviroArmour Aluminum Back Panel 20x16

• 20×16 in. aluminum panel provides a rigid mounting surface for readers and strike hardware.
• Supports 9VDC access control assemblies including reader card slots and strike driver circuits.
• Rated for outdoor/sheltered environments; frame knockouts allow clean cable routing on install.

STI

SKU: BPA2424

STI BPA2424 EnviroArmour Aluminum Back Panel 24x24

• 24×24 aluminum panel distributes load, preventing pull-through on hollow frames.
• EnviroArmour construction resists corrosion for outdoor and mixed-environment installs.
• Supports 9VDC electric strike and magnetic lock mounting in standard configurations.

STI

SKU: BPF0606

STI BPF0606 EnviroArmour Fiberglass Back Panel 6x6

• Fiberglass EnviroArmour construction resists corrosion for outdoor-rated deployments.
• 6×6 in. panel provides structural backing for readers, strikes, and credential hardware.
• Four fixing holes accept 7 mm masonry bits for permanent door-frame or surface mounting.

STI

SKU: BPF0806

STI BPF0806 EnviroArmour Fiberglass Back Panel 8x6

• Fiberglass construction resists UV, moisture, and corrosion in outdoor deployments.
• Non-conductive backing provides electrical isolation where metal enclosures are unsuitable.
• Supports 9VDC electromechanical strikes and standard reader brackets in an 8×6 in. form.

STI

SKU: BPF0808

STI BPF0808 EnviroArmour Fiberglass Back Panel 8x8

• Fiberglass construction resists moisture, UV, and physical stress in outdoor installs.
• 8×8 inch footprint accommodates standard reader, strike, and control module hardware.
• Four 7mm masonry mount points allow direct wall-templating for fast, repeatable installs.

STI

SKU: BPF1008

STI BPF1008 EnviroArmour Fiberglass Back Panel 10x8

10x8 fiberglass back panel shields access control in outdoor/wet conditions

• Weatherproof protection for readers, strike hardware, and cabling outdoors
• Fiberglass construction with environmental sealing resists UV and corrosion
• Mounts behind STI 9VDC access control systems on doors and frames

STI

SKU: BPF1210

STI BPF1210 EnviroArmour Fiberglass Back Panel 12x10

• Fiberglass construction resists salt spray, UV, and moisture for outdoor deployments.
• Pre-drilled four-hole pattern fits standard electrical boxes and door frame cavities.
• Rated for 9VDC hardware; supply gasket inserts seal cable entries against water intrusion.

STI

SKU: BPF1412

STI BPF1412 EnviroArmour Fiberglass Back Panel 14x12

• Fiberglass construction resists moisture, UV, and corrosion in outdoor deployments.
• 14×12-inch panel accommodates readers, keypads, and strike assemblies without custom fab.
• Operates at 9VDC, compatible with standard access control power supplies and controllers.

STI

SKU: BPF1614

STI BPF1614 EnviroArmour Fiberglass Back Panel 16x14

• Fiberglass construction resists salt spray, UV, and corrosion in outdoor installations.
• Supports 9VDC powered strikes without flex or crack propagation under repeated impact.
• Four M8 fixing holes enable secure mounting in surface or recessed door frame configs.

STI

SKU: BPF2016

STI BPF2016 EnviroArmour Fiberglass Back Panel 20x16

• Fiberglass substrate resists weather and mechanical stress at exterior door installations.
• 20×16-inch panel consolidates EM locks, mag strikes, and readers on one rigid surface.
• Supports 9VDC strike hardware and card, keypad, or biometric reader mounting.

STI

SKU: BPP0606

STI BPP0606 EnviroArmour Polycarbonate Back Panel 6x6

6x6 polycarbonate back panel with EnviroArmour for outdoor access control

• Weatherproof polycarbonate construction rated for outdoor and high-traffic use
• Surface-mount design compatible with STI readers, keypads, and access hardware
• 9VDC operation integrates with standard access control power supplies